Conventional labyrinth seal applications in turbomachinery encounter a permanent teeth tip damage and wear during transitional operations. This is the dominant issue that causes unpredictable seal leakage performance degradation. Since the gap between the rotor and the stator changes depending on engine transitional operations, labyrinth teeth located on the rotor/stator wear against the stator/rotor. This wear is observed mostly in the form of the labyrinth teeth becoming a mushroom shape. It is known that, as a result of this tooth tip wear, leakage performance permanently decreases, which negatively affects the engine's overall efficiency. However, very limited information about leakage performance degradation caused by mushroom wear is available in open literature. This paper presents a study that numerically quantifies leakage values for various radii of mushroom-shaped labyrinth teeth by changing tooth-surface clearance, pressure ratio, number of teeth, and rotor speed. Analyzed parameters and their ranges are mushroom radius (R = 0–0.508 mm), clearance (cr = 0.254–2.032 mm), pressure ratio (Rp = 1.5–3.5), number of teeth (nt = 1–12), and rotor speed (n = 0–80 krpm). Computational fluid dynamics (CFD) analyses were carried out by employing compressible turbulent flow in 2D axisymmetrical coordinate system. CFD leakage results were also compared with well-known labyrinth seal semi-empirical correlations. Given a constant clearance, leakage increases with the size of the mushroom radius that forms on the tooth. This behavior is caused by less flow separation and flow disturbance, and the vena contracta effect for flow over the smoothly shaped mushroom tooth tip compared to the sharp-edged tooth tip. This leakage increase is higher when the tooth tip wear is considered as an addition to the unworn physical clearance, since the clearance dominates the leakage. The leakage affected by the number of teeth was also quantified with respect to the mushroom radius. The rotational effect was also studied as a secondary parameter.
Skip Nav Destination
Article navigation
March 2016
Research-Article
Computational Fluid Dynamics Investigation of Labyrinth Seal Leakage Performance Depending on Mushroom-Shaped Tooth Wear
Yahya Dogu,
Yahya Dogu
Department of Mechanical Engineering,
Kirikkale University,
Yahsihan, Kirikkale 71450, Turkey
e-mail: yahya.dogu@hotmail.com
Kirikkale University,
Yahsihan, Kirikkale 71450, Turkey
e-mail: yahya.dogu@hotmail.com
Search for other works by this author on:
Mustafa C. Sertçakan,
Mustafa C. Sertçakan
Department of Mechanical Engineering,
Kirikkale University,
Yahsihan, Kirikkale 71450, Turkey
e-mail: mcem_sertcakan@hotmail.com
Kirikkale University,
Yahsihan, Kirikkale 71450, Turkey
e-mail: mcem_sertcakan@hotmail.com
Search for other works by this author on:
Ahmet S. Bahar,
Ahmet S. Bahar
Department of Mechanical Engineering,
Kirikkale University,
Yahsihan, Kirikkale 71450, Turkey
e-mail: ahmetserhatbahar@gmail.com
Kirikkale University,
Yahsihan, Kirikkale 71450, Turkey
e-mail: ahmetserhatbahar@gmail.com
Search for other works by this author on:
Mustafa Kocagül
Mustafa Kocagül
Search for other works by this author on:
Yahya Dogu
Department of Mechanical Engineering,
Kirikkale University,
Yahsihan, Kirikkale 71450, Turkey
e-mail: yahya.dogu@hotmail.com
Kirikkale University,
Yahsihan, Kirikkale 71450, Turkey
e-mail: yahya.dogu@hotmail.com
Mustafa C. Sertçakan
Department of Mechanical Engineering,
Kirikkale University,
Yahsihan, Kirikkale 71450, Turkey
e-mail: mcem_sertcakan@hotmail.com
Kirikkale University,
Yahsihan, Kirikkale 71450, Turkey
e-mail: mcem_sertcakan@hotmail.com
Ahmet S. Bahar
Department of Mechanical Engineering,
Kirikkale University,
Yahsihan, Kirikkale 71450, Turkey
e-mail: ahmetserhatbahar@gmail.com
Kirikkale University,
Yahsihan, Kirikkale 71450, Turkey
e-mail: ahmetserhatbahar@gmail.com
Altuğ Pişkin
Ercan Arıcan
Mustafa Kocagül
1Corresponding author.
Contributed by the Structures and Dynamics Committee of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received July 15, 2015; final manuscript received August 12, 2015; published online September 29, 2015. Editor: David Wisler.
J. Eng. Gas Turbines Power. Mar 2016, 138(3): 032503 (10 pages)
Published Online: September 29, 2015
Article history
Received:
July 15, 2015
Revised:
August 12, 2015
Citation
Dogu, Y., Sertçakan, M. C., Bahar, A. S., Pişkin, A., Arıcan, E., and Kocagül, M. (September 29, 2015). "Computational Fluid Dynamics Investigation of Labyrinth Seal Leakage Performance Depending on Mushroom-Shaped Tooth Wear." ASME. J. Eng. Gas Turbines Power. March 2016; 138(3): 032503. https://doi.org/10.1115/1.4031369
Download citation file:
Get Email Alerts
An Experimental Comparison of Methanol Combustion Strategies: Spark Ignition Versus Compression Ignition
J. Eng. Gas Turbines Power
Systems-Based Approach To Predicting Tbc Delamination Due To Cmas Infiltration
J. Eng. Gas Turbines Power
Related Articles
Evaluation of Flow Behavior for Clearance Brush Seals
J. Eng. Gas Turbines Power (January,2008)
Numerical Investigations of Leakage Performance Degradations in Labyrinth and Flexible Seals Due to Wear
J. Eng. Gas Turbines Power (May,2021)
Computational Fluid Dynamics Investigation of Brush Seal Leakage Performance Depending on Geometric Dimensions and Operating Conditions
J. Eng. Gas Turbines Power (March,2016)
Experimental Investigation and Mathematical Modeling of Clearance Brush Seals
J. Eng. Gas Turbines Power (July,1998)
Related Proceedings Papers
Related Chapters
Aerodynamic Performance Analysis
Axial-Flow Compressors
Antilock-Braking System Using Fuzzy Logic
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3
Boundary Layer Analysis
Centrifugal Compressors: A Strategy for Aerodynamic Design and Analysis