Experimental dynamic force coefficients are presented for a four pad flexure-pivot tilting-pad bearing in load-between-pad configuration for a range of rotor speeds and bearing unit loadings. Measured dynamic coefficients have been compared to theoretical predictions using an isothermal analysis for a bulk-flow Navier-Stokes (NS) model. Predictions from two models—the Reynolds equation and a bulk-flow NS equation models are compared to experimental, complex dynamic stiffness coefficients (direct and cross-coupled) and show the following results: (i) The real part of the direct dynamic-stiffness coefficients is strongly frequency dependent because of pad inertia, support flexibility, and the effect of fluid inertia. This frequency dependency can be accurately modeled for by adding a direct added-mass term to the conventional stiffness/damping matrix model. (ii) Both models underpredict the identified added-mass coefficient $(∼32kg)$, but the bulk-flow NS equation predictions are modestly closer. (iii) The imaginary part of the direct dynamic-stiffness coefficient (leading to direct damping) is a largely linear function of excitation frequency, leading to a constant (frequency-independent) direct damping model. (iv) The real part of the cross-coupled dynamic-stiffness coefficients shows larger destabilizing forces than predicted by either model. The frequency dependency that is accounted for by the added mass coefficient is predicted by the models and arises (in the models) primarily because of the reduction in degrees of freedom from the initial 12 degrees (four pads times three degrees of freedom) to the two-rotor degrees of freedom. For the bearing and condition tested, pad and fluid inertia are secondary considerations out to running speed. The direct stiffness and damping coefficients increase with load, while increasing and decreasing with rotor speed, respectively. As expected, a small whirl frequency ratio (WFR) was found of about 0.15, and it decreases with increasing load and increases with increasing speed. The two model predictions for WFR are comparable and both underpredict the measured WFR values. Rotors supported by either conventional tilting-pad bearings or flexure-pivot tilting-pad (FPTP) bearings are customarily modeled by frequency-dependent stiffness and damping matrices, necessitating an iterative calculation for rotordynamic stability. For the bearing tested and the load conditions examined, the present results show that adding a constant mass matrix to the FPTP bearing model produces an accurate frequency-independent model that eliminates the need for iterative rotordynamic stability calculations. Different results may be obtained for conventional tilting-pad bearings (or this bearing at higher load conditions).

1.
Armentrout
,
R. D.
, and
Paquette
,
D. J.
, 1993, “
Rotordynamic Characteristics of Flexure-Pivot Tilting-Pad Journal Bearings
,”
Tribol. Trans.
1040-2004,
36
, pp.
443
451
.
2.
Kepple
,
W. E.
,
,
D. W.
,
Zeidan
,
F. Y.
,
,
C.
, and
Dawson
,
M. P.
, 1998, “
Experience in the Use of Flexure Pivot Tilt Pad Bearings in Boiler Feed Water Pumps
,”
Proceedings of the 15th International Pump Users Symposium
,
Houston
, Turbomachinery Laboratory, College Station, TX, pp.
77
84
.
3.
Zeidan
,
F. Y.
, 1992, “
Developments in Fluid Film Bearing Technology
,”
Turbomach. Int.
,
9
, pp.
24
31
.
4.
Lund
,
J.
, 1964, “
Spring and Damping Coefficients for the Tilting Pad Journal Bearing
,”
ASLE Trans.
0569-8197,
7
, pp.
342
352
.
5.
Reinhardt
,
E.
, and
Lund
,
J.
, 1975, “
The Influence of Fluid Inertia on the Dynamic Properties of Journal Bearings
,”
ASME J. Lubr. Technol.
0022-2305,
97
, pp.
159
167
.
6.
San Andrés
,
L. A.
, 1996, “
Turbulent Flow, Flexure-Pivot Hybrid Bearings for Cryogenic Applications
,”
Trans. ASME
,
118
, pp.
190
200
.
7.
Parsell
,
J. K.
,
Allaire
,
P. E.
, and
Barrett
,
L. E.
, 1982, “
Frequency Effects in Tilting-Pad Journal Bearing Dynamic Coefficients
,”
ASLE Trans.
0569-8197,
26
, pp.
222
227
.
8.
Barret
,
L.
,
Allaire
,
P.
, and
Wilson
,
B.
, 1987, “
The Eigenvalue Dependence of Reduced Tilting Pad Bearing Stiffness and Damping Coefficients
,”
Tribol. Trans.
1040-2004,
31
, pp.
411
419
.
9.
Ha
,
H. C.
, and
Yang
,
S. H.
, 1999, “
Excitation Frequency Effects on the Stiffness and Damping Coefficients of a Five-Pad Tilting Pad Journal Bearing
,”
ASME J. Tribol.
0742-4787,
121
, pp.
517
522
.
10.
Rodriguez
,
L.
, and
Childs
,
D. W.
, 2004, “
Experimental Rotordynamic Coefficient Results for a Load-on-Pad Flexible-Pivot Tilting-Pad Bearing With Comparisons to Predictions From Bulk-Flow and Reynolds Equation Models
,” ASME/STLE Joint Tribology Conference, ASME/STLE Paper No. TRIB2004-64042, Long Beach, CA, October.
11.
Childs
,
D. W.
, and
Hale
,
K.
, 1994, “
A Test Apparatus and Facility to Identify the Rotordynamic Coefficients of High-Speed Hydrostatic Bearings
,”
ASME J. Tribol.
0742-4787,
116
, pp.
337
344
.
12.
San Andrés
,
L. A.
, 1995, “
Bulk-Flow Analysis of Flexure and Tilting Pad Fluid Film Bearings
,” Turbomachinery Laboratory, Texas A&M University, College Station, Report No. TRC-B&C-3-95.
13.
Lund
,
J.
, 1965, “
The Stability of an Elastic Rotor in Journal Bearings with Flexible Damped Supports
,”
ASME J. Appl. Mech.
0021-8936,
87
, pp.
911
920
.
14.
San Andrés
,
L. A.
, 1991, “
Effect of Eccentricity on the Force Response of a Hybrid Bearing
,”
STLE Tribol. Trans.
1040-2004,
34
(
4
), pp.
537
544
.
15.
Zeidan
,
F. Y.
, and
Paquette
,
D. J.
, 1994, “
Application of High Speed and High Performance Fluid Film Bearings in Rotating Machinery
,”
Proceedings of the 23rd Turbomachinery Symposium
, Dallas, Turbomachinery Laboratory, College Station, TX, pp.
209
234
.