All major manufacturers of large size gas turbines are developing new techniques aimed at achieving net electric efficiency higher than 60% in combined cycle applications. An essential factor for this goal is the effective cooling of the hottest rows of the gas turbine. The present work investigates three different approaches to this problem: (i) the most conventional open-loop air cooling; (ii) the closed-loop steam cooling for vanes and rotor blades; (iii) the use of two independent closed-loop circuits: steam for stator vanes and air for rotor blades. Reference is made uniquely to large size, single shaft units and performance is estimated through an updated release of the thermodynamic code GS, developed at the Energy Department of Politecnico di Milano. A detailed presentation of the calculation method is given in the paper. Although many aspects (such as reliability, capital cost, environmental issues) which can affect gas turbine design were neglected, thermodynamic analysis showed that efficiency higher than 61% can be achieved in the frame of current, available technology.

Issue Section:
Gas Turbines: Electric Power
Keywords:
gas turbines, combined cycle power stations, rotors, stators, cooling, thermodynamics
Topics:
Blades, Cooling, Flow (Dynamics), Gas turbines, Rotors, Steam, Coolants, Temperature, Calibration
1.
DuBose, P. E. et al., 2001, “Testing the World’s Largest Gas Turbines,” ASME Paper 2001-GT-0398.
2.
Maekawa, A. et al., 2001, “Development of H Series Gas Turbines,” ASME 2001-GT-0500.
3.
Gaul, G. R., and Dodd, A. M., 2001, “The W501G Testing and Validation in the Siemens-Westinghouse Advanced Turbine Systems Program,” ASME Paper 2001-GT-0399.
4.
Eckardt, D., and Rufli, P., 2001, “Advanced Gas Turbine Technology—ABB/BBC Historical Firsts,” ASME Paper 2001-GT-0395.
5.
Consonni, S., 1992, “Performance Prediction of Gas/Steam Cycles for Power Generation,” MAE Dept. Ph.D. Thesis n. 1983-T, Princeton University, Princeton, NJ.
6.
Young, J. B., and Wilcock, R. C., 2001, “Modelling the Air-Cooled Gas Turbine: Part 1—General Thermodynamics,” ASME Paper 2001-GT-0385
7.
Chiesa, P., Consonni, S., and Lozza, G., 1998, “A Comparative Analysis of IGCCs With CO2 Sequestration,” Proc. of 4th International Conference on Greenhouse Gas Control Technologies, Interlaken, Switzerland, Pergamon, Oxford, pp. 107–112.
8.
Campanari, S., and Macchi, E., 1998, “Thermodynamic Analysis of Advanced Power Cycles Based Upon Solid Oxide Fuel Cells, Gas Turbines And Rankine Cycles,” ASME Paper 98-GT-585.
9.
Macchi
,
E.
et al.,
1995
, “
An Assessment of the Thermodynamic Performance of Mixed Gas-Steam Cycles. Part A: Intercooled and Steam Injected Cycles—Part B: Water-Injected and HAT Cycles
,”
ASME J. Eng. Gas Turbines Power
,
117
, pp.
489
–
508
.
10.
Lozza, G., 1990, “Bottoming Steam Cycles for Combined Gas-Steam Power Plants: A Theoretical Estimation of Steam Turbine Performance and Cycle Analysis,” Proc. of 1990 ASME Cogen-Turbo, New Orleans, LA, ASME, New York, pp. 83–92.
11.
Macchi
,
E.
, and
Perdichizzi
,
A.
,
1981
, “
Efficiency Prediction for Axial-Flow Turbines Operating With Non-Conventional Fluids
,”
ASME J. Eng. Gas Turbines Power
,
103
, pp.
718
–
724
.
12.
Consonni et al., 1991, “Gas-Turbine-Based Advanced Cycles for Power Generation. Part A: Calculation Model,” Proc. of the Yokohama International Gas Turbine Congress, Yokohama, Japan.
13.
Chiesa et al., 1993, “Predicting the Ultimate Performance of Advanced Power Cycles Based on Very High Temperature Gas Turbine Engines,” ASME Paper 93-GT-223.
14.
Louis, J. F., 1997, “Systematic Studies of Heat Transfer and Film Cooling Effectiveness,” AGARD CP-229, Neuilly sur Seine, France.
15.
Dailey, G., 2003, “Aero-Thermal Performance of Internal Cooling System in Turbomachines: Design and Calculation Issues,” von Karman Institute Lecture Series 2000-03, Rhode Saint Genese, Belgium.
16.
Taslim, M. E., 2003, “Aero-Thermal Performance of Internal Cooling System in Turbomachines: Convective Cooling in Non-Rotating and Rotating Channels: Experimental Aspects,” von Karman Institute Lecture Series 2000-03, Rhode Saint Genese, Belgium.
17.
Strang, A., 1979, “High Temperature Properties of Coated Superalloys,” Proc. of Behavior of High Temperature Alloys in Aggressive Environments, Petten, The Netherlands, The Metals Society, London, pp. 595–611.
18.
Jorda, K., Torbidoni, L., and Massardo, A. F., 2001, “Convective Blade Cooling Modelling for the Analysis of Innovative Gas Turbine Cycles,” ASME Paper 2001-GT-0390.
19.
Goldstein, R. J., and Haji-Sheikh, H., 1967, “Prediction of Film Cooling Effectiveness,” Proc. of 1967 Semi-International Symposium, JSME, Tokyo, Japan, pp. 213–218.
20.
Johnston, J. R., 2000, “Performance and Reliability Improvements for Heavy-Duty Gas Turbines,” Report GER-3571H GE Power Systems, Schenectady, NY.
21.
Brooks, F. J., 2000, “GE Gas Turbine: Performance Characteristics,” Report GER-3567H, GE Power Systems, Schenectady NY.
22.
Chase, D. L., and Kehoe, P. T., 2000, “GE Combined-Cycle Product Line and Performance,” Report GER-3574G, GE Power Systems, Schenectady, NY.
23.
Streb, H. et al., 2001, “Advanced Burner Development for the VX4.3A Gas Turbine,” ASME Paper 2001-GT-0077.
24.
Siemens Power Generation website: www.pg.siemens.com/en/index.cfm.
25.
Alstom Power website: www.power.alstom.com.
26.
Gas Turbine World 2000-2001 Handbook, Vol. 21, Pequot Publishing, Fairfield, CT.
27.
Kallianpur, V., Akita, E., and Tsukuda, Y. 2001, “Enhancing Reliability & Reducing O&M Expenditures in Advanced Combined Cycle Gas Turbine Power Plants,” ASME Paper 2001-GT-0499.
28.
Fulton
,
K.
, and
Farmer
,
R.
,
1997
, “
Takasago 330-MW Combined Cycle is Tested for Steam-Cooled 501 G
,”
Gas Turbine World
,
27
(
2
),
March/April
March/April
.
29.
Anon., 1998, “ABB Brings GT24 With Once-Through Boiler to New England Merchant Plant,” Turbomachinery International, Jan.–Feb.
30.
“The GT24/GT26 Gas Turbine,” 1998, ABB Report PGT2186.
31.
Matta, R. K., Mercer, G. D., and Tuthill, R. S., 2000, “Power Systems for the 21st Century—‘H’ Gas Turbine Combined-Cycles,” GER-3935B, GE Power Systems, Schenectady, NY.
32.
Tomlinson, L. O. et al., 1995, “Advanced Technology Combined Cycles,” Report GER-3936, GE Power Systems, Schenectady, NY.
Copyright © 2004
 by ASME
You do not currently have access to this content.