The paper presents the development of a methodology for evaluating the torque nonuniformity between the various cylinders of an internal combustion engine (ICE). This nonuniformity can be due, for example, to pathological operating conditions such as misfires or misfuels, as well as to other abnormal operating conditions. Between the nominal torque production and the one corresponding to the absence of combustion there exist, in fact, a series of possible intermediate conditions. Each of them corresponds to a value of produced torque that lies between the nominal value and the one corresponding to the lack of combustion (due for example to statistical dispersion in manufacturing or aging in the injection system). The diagnosis of this type of nonuniformity is a very important issue in today’s engine control strategies design. The use of the developed methodology should in fact allow the control strategy to adopt the appropriate interventions if the diagnosed nonuniformity is related to different behavior of the injectors. In order to evaluate this torque production variability between the various cylinders, information hidden in the instantaneous crankshaft speed fluctuations has been processed using a suitable methodology. The procedure has been validated running a supercharged 2.0 liters V6 engine, and a 1.2 liters L4 engine, in a test cell. During the tests, the in-cylinder pressure signal has been acquired together with the instantaneous engine speed, in order to determine a correlation between speed fluctuations and the indicated torque produced by each cylinder. The actual cylinder-by-cylinder torque nonuniformity can then be evaluated on-board by processing engine speed. The procedure is able to diagnose the absence of combustion (due for example to a misfire or a misfuel) as well as abnormal combustions that do not necessarily involve lack of combustion, with, the accuracy needed for on-board use. Control interventions to injection and ignition time commands of one or more cylinders should, in most cases, be able to re-establish torque production uniformity.

California Air Resources Board, 1991, “Technical Status Update and Proposed Revisions to Malfunction and Diagnostic System Requirements Applicable to 1994 and Subsequent California Passenger Cars, Light-Duty Trucks, and Medium-Duty Vehicles—(OBD II),” CARB Staff Report.
Forster, J., Lohmann, A., Mezger, M., and Ries-Muller, K., 1997, “Advanced Engine Misfire Detection for SI-Engines,” SAE Technical Paper 970855.
Klenk, M., Moser, W., Muller, W., and Wimmer, W., 1993, “Misfire Detection by Evaluating Crankshaft Speed—A Means to Comply With OBD II,” SAE Paper 930399.
Plapp, G., Klenk, M., and Moser, W., 1990, “Methods of On-Board Misfire Detection,” SAE Technical Paper 900232.
Azzoni, P. M., Moro, D., Porceddu-Cilione, C. M., and Rizzoni, G., 1996, “Misfire Detection in a High Performance Engine by the Principal Components Analysis Approach,” SAE Technical Paper 960622.
Azzoni, P. M., Cantoni, G., Ceccarani, M., Mazzetti, S., Minelli, G., Moro, D., and Rizzoni, G., 1995, “Measurement of Engine Misfire in a Lamborghini V-12 Engine Using Crankshaft Speed Fluctuations,” SAE Technical Paper 950837.
Azzoni, P. M., Minelli, G., and Moro, D., 1998, “Misfire Pattern Recognition in High Performance SI 12 Cylinder Engine,” SAE Technical Paper 980521.
Cavina, N., Ponti, F., and Rizzoni, G., 1999, “Fast Algorithm for On-Board Torque Estimation,” SAE Technical Paper 1999-01-0541.
Azzoni, P., Moro, D., Ponti, F., and Rizzoni, G., 1998, “Engine and Load Torque Estimation With Application to Electronic Throttle Control,” SAE Technical Paper 980795.
Citron, S. J., O’Higgins, J. E., and Chen, L. Y., 1989, “Cylinder by Cylinder Engine Pressure and Pressure Torque Waveform Determination Utilizing Speed Fluctuations,” SAE Technical Paper 890486.
Moro, D., Ponti, F., and Cavina, N., 1999, “In-Cylinder Pressure Reconstruction Based on Instantaneous Engine Speed Signal,” Proceedings of ICE Division, Oct. 16–20, 1999, Ann Arbor, MI, ASME, New York.
Letenturier, P., and Benning, J., 1999, “Enhanced Engine Position Acquisition and Treatment,” SAE Technical Paper 1999-01-0203.
Heywood, J. B., 1988, Internal Combustion Engine Fundamentals, McGraw-Hill, New York.
Moskwa, J., Wang, W., and Bucheger, D. J., 1998, “A New Methodology for Engine Diagnostics and Control Utilizing “Synthetic” Engine Variables: Theoretical and Experimental Results,” Proceedings of the ASME Dynamic Systems and Control Division, DSC-Vol. 64, ASME, New York.
You do not currently have access to this content.