To overcome the tradeoff between NOx and particulate emissions for future diesel vehicles and engines it is necessary to seek methods to lower pollutant emissions. The desired simultaneous improvement in fuel efficiency for future DI diesels is also a difficult challenge due to the combustion modifications that will be required to meet the exhaust emission mandates. This study demonstrates the emission reduction capability of EGR and other parameters on a high-speed direct-injection (HSDI) diesel engine equipped with a common rail injection system using an RSM optimization method. Engine testing was done at 1757 rev/min, 45% load. The variables used in the optimization process included injection pressure, boost pressure, injection timing, and EGR rate. RSM optimization led engine operating parameters to reach a low-temperature and premixed combustion regime called the MK combustion region, and resulted in simultaneous reductions in NOx and particulate emissions without sacrificing fuel efficiency. It was shown that RSM optimization is an effective and powerful tool for realizing the full advantages of the combined effects of combustion control techniques by optimizing their parameters. It was also shown that through a close observation of optimization processes, a more thorough understanding of HSDI diesel combustion can be provided.

Issue Section:
Emissions
Keywords:
internal combustion engines, response surface methodology, air pollution control, transportation
Topics:
Common rail fuel injectors, Diesel engines, Emissions, Engines, Exhaust gas recirculation, Nitrogen oxides, Optimization, Response surface methodology, Pressure, Combustion
1.
Walsh, M. P., 1998, “Global Trends in Diesel Emissions Control—A 1998 Update,” SAE Paper No. 980186.
2.
Tanin, K. V., Wickman, D. D., Montgomery, D. T., Das, S., and Reitz, R. D., 1999, “The Influence of Boost Pressure on Emissions and Fuel Consumption of a Heavy-Duty Single-Cylinder D.I. Diesel Engine,” SAE Paper No. 1999-01-0840.
3.
Montgomery, David T., 2000, “An Investigation into Optimization of Heavy-Duty Diesel Engine Operating Parameters When Using Multiple Injections and EGR,” Ph.D. thesis, University of Wisconsin-Madison.
4.
Tow, T. C., Pierpont, A. and Reitz, R. D., 1994, “Reducing Particulates and NOx Emissions by Using Multiple Injections in a Heavy Duty D.I. Diesel Engine,” SAE Paper No. 940897.
5.
Pierpont, D. A., Montgomery, D. T., and Reitz, R. D., 1995, “Reducing Particulate and NOx Using Multiple Injections and EGR in a D.I. Diesel,” SAE Paper 950217.
6.
Montgomery, Douglas C., 1991, Design and Analysis of Experiments, John Wiley and Sons, New York.
7.
Gardiner, W. P., and Gettinby, G., 1998, Experimental Design Techniques in Statistical Practice, Horwood Publishing.
8.
Lorenzen, Thomas J., and Anderson, Virgil L., 1993, Design of Experiments: A No-Name Approach, Marcel Dekker, New York.
9.
Box, G. E. P., Hunter, W. G., and Hunter, J. S., 1978, Statistics for Experimenters, John Wiley and Sons, New York.
10.
Wickman, D. D., Senecal, O. K., and Reitz, R. D., 2001, “Diesel Engine Combustion Chamber Geometry Optimization Using Genetic Algorithms and Multi-Dimensional Spray and Combustion Modeling,” SAE Paper No. 2001-01-0547.
11.
Kimura, Shuji, et al., 1999, “New Combustion Concept for Ultra-Clean and High-Efficiency Small DI Diesel Engines,” SAE Paper No. 1999-01-3681.
12.
Heywood, J. B., 1988, Internal Combustion Engine Fundamentals, McGraw-Hill, New York.
Copyright © 2003
 by ASME
You do not currently have access to this content.