Micromachined planar orifice nozzles have been developed using MEMS (micro-electro-mechanical systems) technology and tested with commercially produced diesel injection systems. Such a system, properly designed, may have the capability to improve the spray characteristics in DI diesel engines due to improved atomization and fuel-air mixing. To demonstrate this process, 14 microplanar orifice nozzles were fabricated with deep X-ray lithography and electroplating (LIGA) technology. The circular orifice diameters were varied from 40 to 260 microns and the number of orifices varied from one to 169. Three plates with noncircular orifices were also fabricated to examine the effect of orifice shape on spray characteristics. These nozzles were then attached to commercial diesel injectors and the associated injection systems were used in the study of drop sizes. The experiments were carried out at two different injection pressures (around 25 MPa and 80 MPa). Local drop sizes were measured by a laser diffraction technique, and the average drop sizes of the whole sprays were measured by a light extinction technique. The drop sizes were found to depend primarily on the total mass flow area. Coalescence droplet collisions among adjacent sprays were apparent for the multiple orifice nozzles. Nonplanar configurations are under development and may show improved performance.

Issue Section:
Injection and Fuel Air Mixture Preparation
Keywords:
internal combustion engines, nozzles, micromachining, micromechanical devices, LIGA, sprays, drops, laser beam applications, fuel
Topics:
Nozzles, Sprays
1.
Peterson
,
K. E.
,
1982
, “
Silicon as a Mechanical Material
,”
Proc. IEEE
,
70
(
5
), pp.
420
–
457
.
2.
Guckel
,
H.
,
Christenson
,
T.
, and
Skrobis
,
K.
,
1992
, “
Metal Micromechanisms via Deep X-Ray Lithography, Electroplating and Assembly
,”
J. Micromech. Microeng.
,
2
, pp.
225
–
228
.
3.
Rogner
,
A.
,
Eicher
,
J.
,
Munchmeyer
,
D.
,
Peters
,
R-P.
, and
Mohr
,
J.
,
1992
, “
The LIGA Technique—What are the New Opportunities
,”
J. Micromech. Microeng.
,
2
, pp.
133
–
140
.
4.
Guckel, H., Skrobis, K., Christensen, T., and Klein, J., 1994, “Micromechanics for Actuators via Deep X-Ray Lithography,” Proc. SPIE’s 1994 Symposium on Microlithography, SPIE Press, San Jose, CA, pp. 39–47.
5.
Guckel, H., 1995, “Deep X-Ray Lithography for Micromechanics and Precision Engineering,” Synchrotron Radiation Instrumentation (Invited), Advanced Photon Source, Argonne, IL.
6.
Madou, M., 1997, Fundamentals of Microfabrication, CRC Press, Boca Raton, FL.
7.
Gravesen
,
P.
,
Branebjerg
,
J.
, and
Jensen
,
O.
,
1993
, “
Microfluidics a Review
,”
J. Micromech. Microeng.
3
, pp.
168
–
182
.
8.
Gardner, R., Horn, W., Rhoades, M., Wells, M., and Yockey, S., 1989, “Silicon Mocromachined Compound Nozzle,” U.S. Patent Number 4828184.
9.
Hamid, M., Kim, H., Im, K., Lai, M. Nuglisch, H., and Dressler, J., 2000, “Effect of Pressure Modulation on Micro-Machined Port Fuel Injector Performance,” Eighth International Conference on Liquid Atomization & Spray Systems, IOP Publishing Ltd., Pasadena, CA, pp. 546–551.
10.
Snyder, H., 1997, “Efficient Liquid Atomization Using Gas Flows and Novel Micro-Machining Techniques,” Ph.D. thesis, University of Wisconsin, Madison, WI.
11.
Kobori, S., Kamimoto, T., and Kosaka, H., 1996, “Ignition, Combustion and Emissions in a DI Diesel Engine Equipped With a Micro-Hole Nozzle,” SAE Paper No. 960321.
12.
Siebers, D., and Higgins, B., 2001, “Flame Lift-Off on Direct-Injection Diesel Sprays Under Quiescent Conditions,” SAE Paper No. 2001-01-0530.
13.
Baik, S., Goney, K. H., Kang, S., Murphy, J., Blanchard, J., and Corradini, M., 1999, “Development of Micro-Diesel Injector Nozzles via MEMS Technology and Initial Results for Diesel Sprays,” SAE Paper No. 1999-01-3645.
14.
Baik, S., Kang, S., Blanchard, J., and Corradini, M., 2000, ‘Development of Micro-Diesel Injector Nozzles via MEMS Technology and Effects on Spray Characteristics,’ Eighth International Conference on Liquid Atomization & Spray Systems, Pasadena, CA, pp. 782–789.
15.
Baik, S., Blanchard, J., Corradini, M., 2001, “Development of Micro-Diesel Injector Nozzles via MEMS Technology and Effects on Spray Characteristics,” SAE Paper No. 2001-01-0528.
16.
Baik, S., 2001, “Development of Micro-Diesel Injector Nozzles via MEMS Technology and Effects on Spray Characteristics,” Ph.D. thesis, University of Wisconsin, Madison, WI.
17.
Goney, K. H., and Corradini, M., 2000, “Isolated Effects of Ambient Pressure, Nozzle Cavitation and Hole Inlet Geometry on Diesel Injection Spray Characteristics,” SAE Paper No. 2000-01-2043.
18.
El-beshbeeshy, M., Hodges, J., and Corradini, M., 1992, “Image Analysis of Diesel Sprays,” SAE Paper No. 921628.
19.
Bower, G., and Foster, D., 1991, “A Comparison of the Bosch and Zuech Rate of Injection Meters,” SAE Paper No. 910724.
20.
Lefebvre, A. H., 1989, Atomization and Sprays, Taylor and Francis, London.
21.
Ashgriz
,
N.
, and
Poo
,
J. Y.
,
1990
, “
Coalescence and Separation in Binary Collisions of Liquid Drops
,”
J. Fluid Mech.
,
221
, pp.
183
–
204
.
Copyright © 2003
 by ASME
You do not currently have access to this content.