In gas turbine combustors, optimum arrangement between a fuel nozzle and a swirler/prefilmer module must be sought to achieve satisfactory ignition and stability characteristics in addition to reduced level of emissions. However, due to thermal expansion of the combustor or misalignment of the fuel nozzle, the location of a fuel nozzle may vary. Displacement of a fuel nozzle may change the amount of fuel injected to the pre-filming device (usually the inner swirler wall) and the location of attachment, which in turn affects the thickness of pre-filming liquid sheet on the wall. As a result, the spray structure formed by pre-filming airblast atomization may be significantly changed. An experimental investigation is carried out to study the effects of fuel nozzle displacement on the structure of a spray formed by a dual orifice pressure atomizer and a counter-rotating dual swirler. The inner wall of the swirler is designed to be used as a pre-filming device. The behavior of droplets, the flow characteristics of the swirling air flow, and the interaction between droplets and the flow are studied. Optical diagnostic methods including a flow visualization and an Adaptive Phase/Doppler technique are used. Distributions of droplet size, number density, and liquid phase volume flux are presented for various fuel nozzle displacements, in addition to gas phase velocity.

Issue Section:
Gas Turbines: Combustion and Fuel
Keywords:
gas turbines, fuel, sprays, nozzles, engineering, liquid films
Topics:
Displacement, Drops, Flow (Dynamics), Fuels, Nozzles, Sprays, Swirling flow
1.
Lefebvre, A. H., and Miller, D., 1966, “The Development of an Air Blast Atomizer for Gas Turbine Application,” COA-Report-Aero-193, College of Aeronautics, Cranfield, England.
2.
Rizkalla
,
A.
, and
Lefebvre
,
A. H.
,
1975
, “
The Influence of Air and Liquid Properties on Airblast Atomization
,”
ASME J. Eng. Gas Turbines Power
,
97
, No.
3
, pp.
316
–
320
.
3.
Rizk
,
N. K.
, and
Lefebvre
,
A. H.
,
1980
, “
Influence of Liquid Film Thickness on Airblast Atomization
,”
ASME J. Eng. Gas Turbines Power
,
102
, pp.
706
–
710
.
4.
Lorenzetto
,
G. E.
, and
Lefebvre
,
A. H.
,
1977
, “
Measurements of Drop Size on a Plain Jet Airblast Atomizer
,”
AIAA J.
,
15
, No.
7
, pp.
1006
–
1010
.
5.
Jasuja
,
A. K.
,
1979
, “
Atomization of Crude and Residual Fuel Oils
,”
ASME J. Eng. Gas Turbines Power
,
101
, No.
2
, pp.
250
–
258
.
6.
El-Shanawany
,
M. S. M. R.
, and
Lefebvre
,
A. H.
,
1980
, “
Airblast Atomization: The Effect of Linear Scale on Mean Drop Size
,”
J. Energy
,
4
, No.
4
, pp.
184
–
189
.
7.
Sattlemayer
,
T.
, and
Wittig
,
S.
,
1986
, “
Internal Flow Effects in Prefilming Airblast Atomizers: Mechanisms of Atomization and Droplet Spectra
,”
ASME J. Eng. Gas Turbines Power
,
108
, pp.
465
–
472
.
8.
Wittig
,
S.
,
Himmelsbach
,
J.
,
Noll
,
B.
,
Feld
,
H. J.
, and
Samenfink
,
W.
,
1992
, “
Motion and Evaporation of Shear-Driven Liquid Films in Turbulent Gases
,”
ASME J. Eng. Gas Turbines Power
,
114
, pp.
395
–
400
.
9.
Bren˜a de la Rosa
,
A.
,
Wang
,
G.
, and
Bachalo
,
W. D.
,
1992
, “
The Effect of Swirl on the Velocity and Turbulence Fields of a Liquid Spray
,”
ASME J. Eng. Gas Turbines Power
,
114
, pp.
72
–
81
.
10.
Wang, H. Y., McDonell, V. G., and Samuelsen, G. S., 1992, “The Two Phase Flow Downstream of a Production Engine Combustor Swirl Cup,” Proceedings, Twenty-Fourth Symposium (International) on Combustion, The Combustion Institute, Pittsburgh, PA, pp. 1457–1463.
11.
Wang, H. Y., McDonell, V. G., and Samuelsen, G. S., 1993, “Influence of Hardware Design on the Flow Field Structures and the Patterns of Droplets Dispersion: Part I—Mean Quantities,” ASME Paper 93-GT-199.
12.
Rizk
,
N. K.
, and
Mongia
,
H. C.
,
1992
, “
Calculation Approach Validation for Airblast Atomizers
,”
Transactions of the ASME
,
114
, April, pp.
386
–
394
.
13.
Lefebvre, A. H., 1995, “The Role of Fuel Preparation in Low Emissions Combustion,” ASME Paper 95-GT-465.
14.
Han, Y. M., Seol, W. S., Yoon, M. S., Lee, D. S., Yagodkin, V. I., and Jeung, I. S., 1997, “An Experimental Study on Modeling of Fuel Atomization for Simulating the Idle Regime of a Gas Turbine Combustor by Atmospheric Testing,” ASME Paper 97-GT-152.
15.
Bach
,
T. V.
, and
Gouldin
,
F. C.
,
1982
, “
Flow Measurements in a Model Swirl Combustor
,”
AIAA J.
,
20
, No.
5
, pp.
642
–
651
.
16.
Blu¨mcke, E., Eickhoff, E., Eassa, C., and Koopman, J., 1987, “Analysis of the Flow Through Double Airblast Atomizers,” AGARD-CP-422, pp. 40_1-40_13.
17.
Wang
,
H. Y.
,
McDonell
,
V. G.
,
Sowa
,
W. A.
, and
Samuelsen
,
G. S.
,
1993
, “
Scaling of the Two-Phase Flow Downstream of a Gas Turbine Combustor Swirl Cup: Part I—Mean Quantities
,”
ASME J. Eng. Gas Turbines Power
,
115
, pp.
453
–
460
.
18.
McDonell, V. G., Lee, S. W., and Samuelsen, G. S., 1994, “Effect of Semi-Confinement on Spray Behavior in the Flow Field Downstream of an Aero-Engine Combustor Dome,” ICLASS-94 Rouen, France, July, Paper VII-6, pp. 726–733.
19.
McDonell, V. G., Lee, S. W., and Samuelsen, G. S., 1995, “Spray Behavior in Reacting and Non-Reacting Flow Fields Downstream of an Aero-Engine Combustor Dome,” in Mechanics and Combustion of Droplets and Sprays, H. H. Chiu, and N. Chigier, eds., Begell, Housers, Inc., New York, pp. 281–294.
Copyright © 2001
 by ASME
You do not currently have access to this content.