The discharge coefficient of a long orifice in a rotating system is measured to examine the rotational effect on discharge behavior. The rotating system is comprised of a rotating disk and two stators on both sides of the rotating disk. Test rig is constructed to simulate the real turbine operating conditions. Pressure ratios between upstream and downstream cavities of the orifice range from 1.05 to 1.8, and rotational speed of the rotor disk is varied up to 10,000 rpm. The orifice hole bored through the rotor disk has length-to-diameter ratio of 10. For a better interpretation of discharge behavior, three-dimensional velocity field in the downstream and upstream cavities of the rotor is measured using a Laser Doppler Velocimetry. A new definition of the rotational discharge coefficient is introduced to consider the momentum transfer from the rotor to the orifice flow. Additional loss in the discharge coefficient due to pressure loss in the orifice hole at the inlet and exit regions is quantitatively presented in terms of the Rotation number and the compressibility factor. The effect of corner radiusing at the orifice inlet is also investigated at various rotational conditions.

1.
Akima
H.
,
1970
, “
A New Method of Interpolation and Smooth Curve Fitting Based on Local Procedures
,”
Journal of Association for Computing Machinery
, Vol.
17
, No.
4
, pp.
589
602
.
2.
Bragg
S. L.
,
1960
, “
Effect of Compressibility on the Discharge Coefficient of Orifices and Convergent Nozzles
,”
Journal of Mechanical Engineering Science
, Vol.
2
, No.
1
, pp.
35
44
.
3.
Hay, N., and Lampard, D., 1996, “Discharge Coefficient of Turbine Cooling Holes: A Review,” ASME Paper 96-GT-492.
4.
Hay
N.
,
Lampard
D.
, and
Benmansour
S.
,
1983
, “
Effect of Crossflows on the Discharge Coefficient of Film Cooling Holes
,”
ASME Journal of Engineering for Power
, Vol.
105
, pp.
243
248
.
5.
Hay, N., Khaldi, A., and Lampard, D., 1987, “Effect of Crossflows on the Coefficient of Discharge of Film Cooling Holes with Rounded Entries or Exits,” Proceedings, 2nd ASME/JSME Thermal Engineering Conference, Hawaii, pp. 369–374.
6.
Hay
N.
, and
Spencer
A.
,
1992
, “
Discharge Coefficients of Cooling Holes with Radiused and Chamfered Inlets
,”
ASME Journal of Turbomachinery
, Vol.
114
, No.
4
, pp.
701
706
.
7.
Jakoby, R., Maeng, D. J., Kim, S., and Wittig, S., 1997, “3D LDA-Measurement in Rotating Turbine Disk Systems,” Proceedings, 7th Int. Conf. Laser Anemometry Advances and Applications, pp. 255–262.
8.
Kline
S. J.
, and
McClintock
F. A.
,
1953
, “
Describing Uncertainties in Single-Sample Experiments
,”
Mechanical Engineering
, Vol.
75
, pp.
3
8
.
9.
Lichtarowicz
A.
,
Duggins
R. K.
, and
Markland
E.
,
1965
, “
Discharge Coefficients for Incompressible Non-Cavitating Flow through Long Orifices
,”
Journal Mechanical Engineering Science
, Vol.
7
, No.
2
, pp.
210
219
.
10.
Maeng, D. J., 1998, “Flow Characteristics and Discharge Behaviors of Highly Rotating Turbine Cavity System with Discharge Holes,” Ph.D. thesis, Seoul National University.
11.
Meyfarth, P. F., and Shine, A. J., 1965, “Experimental Study of Flow Through Moving Orifices,” Journal of Basic Engineering, Dec., pp. 1082–1083.
12.
Saad, M. A., 1993, Compressible Fluid Flow, 2nd ed., Prentice-Hall, Inc., Englewood Cliffs, NJ.
13.
Snyder
P. K.
,
Orloff
K. L.
, and
Reinath
M. S.
,
1984
, “
Reduction of Flow Measurement Uncertainties in Laser Velocimeters with Nonorthogonal Channels
,”
AIAA
, Vol.
22
, No.
8
, pp.
1115
1123
.
14.
Rohde, J., Richard, R., and Metger, G. W., 1969, “Discharge Coefficients for Thick Plate Orifices With Approach Flow Perpendicular and Inclined to Orifice Axis,” NASA TND-5467.
15.
Waschka
W.
,
Scherer
T.
,
Kim
S.
, and
Wittig
S.
,
1992
, “
Influence of High Rotational Speeds on the Heat Transfer and Discharge Coefficients in Labyrinth Seals
,”
ASME Journal of Turbomachinery
, Vol.
114
, pp.
462
468
.
16.
The Jet Engine, 1986, Rolls-Royce PLC publication, 4th ed.
17.
Visualized Flow, 1988, The Japan Society of Mechanical Engineers, Pergamon Press, Inc., Tarrytown, NY.
This content is only available via PDF.