Bubbles populations in the wake of a partial cavity resulting from gas diffusion were measured to determine the noncondensable gas flux into the cavity. The diffusion rate is related to the dissolved gas content, the local cavity pressure, and the flow within and around the cavity. The measurements are used to revisit various scaling relationships for the gas diffusion, and it is found that traditional scaling that assumes the presence of a gas pocket overpredicts the gas diffusion. A new scaling based on diffusion into the low void fraction bubbly mixture within the partial cavity is proposed, and it is shown to adequately scale the observed production of gas bubbles for dissolved air saturation from 30% to 70% at 1 atm, limited cavities on the order of 0.3–3 cm in length at a freestream speed of 8 m/s (σ = 2.3–3.3 and Reynolds number based on the cavity length of order 105).
Skip Nav Destination
Article navigation
Research-Article
Scaling of Gas Diffusion Into Limited Partial Cavities
In-ho Lee,
In-ho Lee
Department of Naval Architecture and
Marine Engineering,
University of Michigan,
1231 Beal Avenue,
2010 Walter E. Lay Automotive Laboratory,
Ann Arbor, MI 48109
e-mail: leeinho@umich.edu
Marine Engineering,
University of Michigan,
1231 Beal Avenue,
2010 Walter E. Lay Automotive Laboratory,
Ann Arbor, MI 48109
e-mail: leeinho@umich.edu
Search for other works by this author on:
Simo A. Mäkiharju,
Simo A. Mäkiharju
Mem. ASME
Department of Naval Architecture and
Marine Engineering,
University of Michigan,
1085 S. University Avenue,
126B West Hall,
Ann Arbor, MI 48109
e-mail: smakihar@umich.edu
Department of Naval Architecture and
Marine Engineering,
University of Michigan,
1085 S. University Avenue,
126B West Hall,
Ann Arbor, MI 48109
e-mail: smakihar@umich.edu
Search for other works by this author on:
Harish Ganesh,
Harish Ganesh
Department of Mechanical Engineering,
University of Michigan,
1231 Beal Avenue,
2010 Walter E. Lay Automotive Laboratory,
Ann Arbor, MI 48109
e-mail: gharish@umich.edu
University of Michigan,
1231 Beal Avenue,
2010 Walter E. Lay Automotive Laboratory,
Ann Arbor, MI 48109
e-mail: gharish@umich.edu
Search for other works by this author on:
Steven L. Ceccio
Steven L. Ceccio
Mem. ASME
Department of Naval Architecture and
Marine Engineering,
University of Michigan,
2600 Draper Drive,
Naval Architecture and Marine
Engineering Building,
Ann Arbor, MI 48109
e-mail: ceccio@umich.edu
Department of Naval Architecture and
Marine Engineering,
University of Michigan,
2600 Draper Drive,
Naval Architecture and Marine
Engineering Building,
Ann Arbor, MI 48109
e-mail: ceccio@umich.edu
Search for other works by this author on:
In-ho Lee
Department of Naval Architecture and
Marine Engineering,
University of Michigan,
1231 Beal Avenue,
2010 Walter E. Lay Automotive Laboratory,
Ann Arbor, MI 48109
e-mail: leeinho@umich.edu
Marine Engineering,
University of Michigan,
1231 Beal Avenue,
2010 Walter E. Lay Automotive Laboratory,
Ann Arbor, MI 48109
e-mail: leeinho@umich.edu
Simo A. Mäkiharju
Mem. ASME
Department of Naval Architecture and
Marine Engineering,
University of Michigan,
1085 S. University Avenue,
126B West Hall,
Ann Arbor, MI 48109
e-mail: smakihar@umich.edu
Department of Naval Architecture and
Marine Engineering,
University of Michigan,
1085 S. University Avenue,
126B West Hall,
Ann Arbor, MI 48109
e-mail: smakihar@umich.edu
Harish Ganesh
Department of Mechanical Engineering,
University of Michigan,
1231 Beal Avenue,
2010 Walter E. Lay Automotive Laboratory,
Ann Arbor, MI 48109
e-mail: gharish@umich.edu
University of Michigan,
1231 Beal Avenue,
2010 Walter E. Lay Automotive Laboratory,
Ann Arbor, MI 48109
e-mail: gharish@umich.edu
Steven L. Ceccio
Mem. ASME
Department of Naval Architecture and
Marine Engineering,
University of Michigan,
2600 Draper Drive,
Naval Architecture and Marine
Engineering Building,
Ann Arbor, MI 48109
e-mail: ceccio@umich.edu
Department of Naval Architecture and
Marine Engineering,
University of Michigan,
2600 Draper Drive,
Naval Architecture and Marine
Engineering Building,
Ann Arbor, MI 48109
e-mail: ceccio@umich.edu
Contributed by the Fluids Engineering Division of ASME for publication in the JOURNAL OF FLUIDS ENGINEERING. Manuscript received November 17, 2014; final manuscript received October 15, 2015; published online January 4, 2016. Assoc. Editor: Olivier Coutier-Delgosha.
J. Fluids Eng. May 2016, 138(5): 051301 (9 pages)
Published Online: January 4, 2016
Article history
Received:
November 17, 2014
Revised:
October 15, 2015
Citation
Lee, I., Mäkiharju, S. A., Ganesh, H., and Ceccio, S. L. (January 4, 2016). "Scaling of Gas Diffusion Into Limited Partial Cavities." ASME. J. Fluids Eng. May 2016; 138(5): 051301. https://doi.org/10.1115/1.4031850
Download citation file:
Get Email Alerts
Related Articles
Shared-Memory Parallelization for Two-Way Coupled Euler–Lagrange Modeling of Cavitating Bubbly Flows
J. Fluids Eng (December,2015)
Probing and Imaging of Vapor–Water Mixture Properties Inside Partial/Cloud Cavitating Flows
J. Fluids Eng (March,2017)
Interfacial Heat Transfer Between Steam Bubbles and Subcooled Water in Vertical Upward Flow
J. Heat Transfer (May,1995)
Experimental Study of Horizontal Bubble Plume With Computational Fluid Dynamics Benchmarking
J. Fluids Eng (November,2016)
Related Proceedings Papers
Related Chapters
Experimental Characterization of a Cavitating Orifice
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Experimental Investigation of Ventilated Supercavitation Under Unsteady Conditions
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Numerical Investigation of the Dynamics of Pressure Loading on a Solid Boundary from a Collapsing Cavitation Bubble
Proceedings of the 10th International Symposium on Cavitation (CAV2018)