Controlling the annular frictional pressure losses is important in order to drill safely with overpressure without fracturing the formation. To predict these pressure losses, however, is not straightforward. First of all, the pressure losses depend on the annulus eccentricity. Moving the drillstring to the wall generates a wider flow channel in part of the annulus which reduces the frictional pressure losses significantly. The drillstring motion itself also affects the pressure loss significantly. The drillstring rotation, even for fairly small rotation rates, creates unstable flow and sometimes turbulence in the annulus even without axial flow. Transversal motion of the drillstring creates vortices that destabilize the flow. Consequently, the annular frictional pressure loss is increased even though the drilling fluid becomes thinner because of added shear rate. Naturally, the rheological properties of the drilling fluid play an important role. These rheological properties include more properties than the viscosity as measured by API procedures. It is impossible to use the same frictional pressure loss model for water based and oil based drilling fluids even if their viscosity profile is equal because of the different ways these fluids build viscosity. Water based drilling fluids are normally constructed as a polymer solution while the oil based are combinations of emulsions and dispersions. Furthermore, within both water based and oil based drilling fluids there are functional differences. These differences may be sufficiently large to require different models for two water based drilling fluids built with different types of polymers. In addition to these phenomena washouts and tool joints will create localised pressure losses. These localised pressure losses will again be coupled with the rheological properties of the drilling fluids. In this paper, all the above mentioned phenomena and their consequences for annular pressure losses will be discussed in detail. North Sea field data is used as an example. It is not straightforward to build general annular pressure loss models. This argument is based on flow stability analysis and the consequences of using drilling fluids with different rheological properties. These different rheological properties include shear dependent viscosity, elongational viscosity and other viscoelastic properties.
Skip Nav Destination
Article navigation
September 2014
Technical Briefs
Annular Frictional Pressure Losses During Drilling—Predicting the Effect of Drillstring Rotation
Arild Saasen
Arild Saasen
1
1Corresponding author.
Search for other works by this author on:
Arild Saasen
1Corresponding author.
Contributed by the Petroleum Division of ASME for publication in the JOURNAL OF ENERGY RESOURCES TECHNOLOGY. Manuscript received July 23, 2013; final manuscript received December 2, 2013; published online March 4, 2014. Assoc. Editor: Christopher J. Wajnikonis.
J. Energy Resour. Technol. Sep 2014, 136(3): 034501 (5 pages)
Published Online: March 4, 2014
Article history
Received:
July 23, 2013
Revision Received:
December 2, 2013
Citation
Saasen, A. (March 4, 2014). "Annular Frictional Pressure Losses During Drilling—Predicting the Effect of Drillstring Rotation." ASME. J. Energy Resour. Technol. September 2014; 136(3): 034501. https://doi.org/10.1115/1.4026205
Download citation file:
Get Email Alerts
Stage-wise kinetic analysis of ammonia addition effects on two-stage ignition in dimethyl ether
J. Energy Resour. Technol
Related Articles
Advanced Geothermal Wellbore Hydraulics Model
J. Energy Resour. Technol (September,2000)
Hydraulic Behavior in Cased and Open-Hole Sections in Highly Deviated Wellbores
J. Energy Resour. Technol (March,2021)
Comprehensive Experimental Investigation of Hole Cleaning Performance in Horizontal Wells Including the Effects of Drill String Eccentricity, Pipe Rotation, and Cuttings Size
J. Energy Resour. Technol (June,2022)
Stick-Slip and Bit-Bounce of Deep-Hole Drillstrings
J. Energy Resour. Technol (June,2000)
Related Proceedings Papers
Related Chapters
Applied Drilling Mechanics
Mechanics of Drillstrings and Marine Risers
A Review on Prediction over Pressured Zone in Hydrocarbon Well Using Seismic Travel Time through Artificial Intelligence Technique for Pre-Drilling Planing
International Conference on Software Technology and Engineering, 3rd (ICSTE 2011)
Well Control
Oilwell Drilling Engineering