The surface temperature of integrated circuit (IC) chips cooled with a single-phase liquid flow increases along the flow direction following the increase in the liquid temperature. Increasing the heat transfer coefficient along the flow direction is an effective way to enhance the cooling performance while mitigating the temperature nonuniformity and high pressure drop concerns. This investigation evaluates numerically the cooling performance of different flow channel designs suitable in 3D IC applications with channel heights restricted to 100 μm. Internal configurations featuring offset strip fins with variable fin density and variable spacing ribs were studied in an effort to minimize the temperature nonuniformity while maintaining a relatively low pressure drop. The performance of 13 different designs for the variable-fin-density configuration and three different rib configurations have been evaluated and compared with two baseline cases, corresponding to a smooth flow channel and a flow channel with continuous fins. All of the analyzed internal configurations are contained within a flow channel of 100 μm height and 910 μm width. A coolant chip formed by nine flow channels for the dissipation of 200 W of a 3D IC with a surface area of 1 cm2 is the base for this investigation. The best performing configuration resulted in a temperature variation of less than 30 K with a pressure drop of 34 kPa as compared to a temperature variation of 38 K and a pressure drop of 144 kPa with continuous fins and 51 K and 21 kPa for a smooth flow channel.
Skip Nav Destination
Article navigation
June 2014
Research-Article
Variable Fin Density Flow Channels for Effective Cooling and Mitigation of Temperature Nonuniformity in Three-Dimensional Integrated Circuits
Daniel Lorenzini-Gutierrez,
Daniel Lorenzini-Gutierrez
Mechanical Engineering Department,
e-mail: ld.lorenzinigutierrez@ugto.mx
Rochester Institute of Technology
,Rochester, NY 14623
e-mail: ld.lorenzinigutierrez@ugto.mx
Search for other works by this author on:
Satish G. Kandlikar
Satish G. Kandlikar
1
Mechanical Engineering Department,
e-mail: sgkeme@rit.edu
Rochester Institute of Technology
,Rochester, NY 14623
e-mail: sgkeme@rit.edu
1Corresponding author.
Search for other works by this author on:
Daniel Lorenzini-Gutierrez
Mechanical Engineering Department,
e-mail: ld.lorenzinigutierrez@ugto.mx
Rochester Institute of Technology
,Rochester, NY 14623
e-mail: ld.lorenzinigutierrez@ugto.mx
Satish G. Kandlikar
Mechanical Engineering Department,
e-mail: sgkeme@rit.edu
Rochester Institute of Technology
,Rochester, NY 14623
e-mail: sgkeme@rit.edu
1Corresponding author.
Contributed by the Electronic and Photonic Packaging Division of ASME for publication in the JOURNAL OF ELECTRONIC PACKAGING. Manuscript received July 30, 2013; final manuscript received February 25, 2014; published online April 29, 2014. Assoc. Editor: Gongnan Xie.
J. Electron. Packag. Jun 2014, 136(2): 021007 (11 pages)
Published Online: April 29, 2014
Article history
Received:
July 30, 2013
Revision Received:
February 25, 2014
Citation
Lorenzini-Gutierrez, D., and Kandlikar, S. G. (April 29, 2014). "Variable Fin Density Flow Channels for Effective Cooling and Mitigation of Temperature Nonuniformity in Three-Dimensional Integrated Circuits." ASME. J. Electron. Packag. June 2014; 136(2): 021007. https://doi.org/10.1115/1.4027091
Download citation file:
Get Email Alerts
Sequential Versus Concurrent Effects in Combined Stress Solder Joint Reliability
J. Electron. Packag
Anand Model Constants of Sn-Ag-Cu Solders: What Do They Actually Mean?
J. Electron. Packag
Related Articles
Review and Projections of Integrated Cooling Systems for Three-Dimensional Integrated Circuits
J. Electron. Packag (June,2014)
Analysis of Liquid-Cooled Heat Sink Used for Power Electronics Cooling
J. Thermal Sci. Eng. Appl (June,2011)
Numerical Prediction of Flow and Heat Transfer in an Impingement Heat
Sink
J. Electron. Packag (March,1997)
Related Proceedings Papers
Related Chapters
Extended-Surface Metallurgy
Heat Exchanger Engineering Techniques
Thermodynamic Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Heat Transfer and Pressure Drop Correlations for Compact Heat Exchangers with Multi-Region Louver Fins
Inaugural US-EU-China Thermophysics Conference-Renewable Energy 2009 (UECTC 2009 Proceedings)