Abstract

The electronics industry, in recent years, has been focusing primarily on product miniaturization and lead-free assembly. The need for product miniaturization is due to the continuous demand for portable electronic products that are multifunctional, yet smaller, faster, cheaper, and lighter. This is forcing the industry to design and assemble products with miniature passive and active devices. These devices typically have fine pitch footprints that provide a very small surface area for attachment. The solder attach technique relies primarily on the formation of intermetallics between the mating metallic surfaces. With a reduction in the surface area of the pads, the ratio of intermetallic to solder is very high once the solder joint is formed. This could result in unreliable solder joints, due to the brittle nature of intermetallics. In addition, the need to eliminate lead-based materials as a means of interconnection has renewed the industry’s interest in exploring other means of assembling surface mount devices reliably. The use of a novel anisotropic conductive adhesive (ACA) as a means for assembling surface mount devices, the ACA’s performance characteristics, and preliminary research findings are discussed in this paper. Typically, ACAs require the application of pressure during the curing process to establish the electrical connection. The novel ACA uses a magnetic field to align the particles in the Z-axis direction and eliminates the need for pressure during curing. The formation of conductive columns within the polymer matrix provides a very high insulation resistance between adjacent conductors. The novel ACA also enables mass curing of the adhesive, eliminating the need for sequential assembly. The novel ACA was found to be very effective in providing the interconnection for surface mount technology (SMT) passives and leaded, bumped, or bumpless integrated circuit packages. The requirement for precise stencil printing was eliminated, as the application of magnetic field aligned the conductive columns in the Z-axis direction eliminating any lateral conductivity. The ability to mass cure the adhesive while applying the magnetic field reduced the assembly time considerably. Placement accuracy was still found to be very critical. Shear testing of adhesive joints after thermal aging showed significance past 500 h and after temperature–humidity aging showed significance within the first 100 h. IV characteristics of the daisy chained ball grid array devices assembled with and without bumps revealed considerable difference in the breakdown current. The correlation between initial contact resistance of the daisy chain and the final breakdown current was also determined. Preliminary experiments and findings, discussed in this paper, show the viability of the ACA for mixed SMT assembly. Further experimentations will include in situ contact resistance measurements during thermal aging, temperature–humidity aging, drop testing and thermal shock.

1.
Gilleo
,
K.
, 1999, “
Introduction to Conductive Adhesive Joining Technology
,”
Conductive Adhesives for Electronics Manufacturing
,
Electrochemical Publications Ltd.
, Bristol, UK, pp.
1
16
.
2.
Li
,
H.
, and
Wong
,
C. P.
, 2004, “
A Reworkable Epoxy Resin for Isotropically Conductive Adhesive
,”
IEEE Trans. Adv. Packag.
1521-3323,
27
(
1
), pp.
165
172
.
3.
Baldan
,
A.
, 2004, “
Adhesively-Bonded Joints and Repairs in Metallic Alloys, Polymer and Composite Materials: Adhesives, Adhesion Theories and Surface Pretreatment
,”
J. Mater. Sci.
0022-2461,
39
, pp.
1
49
.
4.
Lau
,
J. H.
,
Wong
,
C. P.
,
Lee
,
N. C.
, and
Lee
,
R. S. W.
, 2003,
Electronics Manufacturing: With Lead-Free, Halogen-Free, and Conductive-Adhesive Materials
,
McGraw–Hill
, New York.
5.
Fan
,
L.
,
Tison
,
C.
, and
Wong
,
C. P.
, 2002, “
Fundamental Understanding of Conductivity Establishment for Electrically Conductive Adhesives
,”
Proceedings of the 52nd Electronic Components and Technology Conference
, San Diego, CA, May 28–31, 2002, pp.
1154
1157
.
6.
Wong
,
C. P.
, and
Lu
,
D.
, 1998, “
Lubricants of Silver Fillers for Conductive Adhesive Applications
,”
Proceedings of 3rd International Conference on Adhesive Joining and Coating Technology in Electronics Manufacturing
, Binghamton, N.Y., September 28–30, 1998, pp.
184
192
.
7.
Watanabe
,
I.
, and
Takemura
,
K.
, 1999, “
Anisotropic Conductive Adhesive Films for Flip-Chip Interconnection
,”
Conductive Adhesives for Electronics Manufacturing
,
Electrochemical Publications Ltd.
, Bristol, UK, pp.
256
270
.
8.
Liu
,
J.
, 1995, “
Development of Conductive Adhesive Joining for Surface-Mounting Electronics Manufacturing
,”
IEEE Trans. Compon., Packag. Manuf. Technol., Part B
1070-9894,
18
(
2
), pp.
313
319
.
9.
Jin
,
S.
,
Sherwood
,
R. C.
,
Mottine
,
J. J.
,
Tiefel
,
T. H.
, and
Opila
,
R. L.
,
J. Appl. Phys.
0021-8979,
64
, pp.
6008
6010
.
10.
Jin
,
S.
,
Tiefel
,
T. H.
, and
Wolfe
,
R.
, 1992, “
Directionally-Conductive, Optically-Transparent Composites by Magnetic Alignment
,”
IEEE Trans. Magn.
0018-9464,
28
, pp.
2211
2213
.
11.
Sancaktar
,
E.
, and
Dilsiz
,
N.
, 1997, “
Anisotropic Alignment of Nickel Particles in a Magnetic Field for Electronically Conductive Adhesives Applications
,”
J. Adhes. Sci. Technol.
0169-4243,
11
, pp.
155
166
.
12.
Breval
,
E.
,
Klimkiewicz
,
M.
,
Shi
,
Y. T.
,
Arakaki
,
D.
, and
Dougherty
,
J. P.
, 2003, “
Magnetic Alignment of Particles in Composite Films
,”
J. Mater. Sci.
0022-2461,
38
, pp.
1347
1351
.
You do not currently have access to this content.