The current numerical investigation will examine the effect of an impinging mixed convection air jet on the heat transfer rate of a parallel flat plate heat sink. A three-dimensional numerical model was developed to evaluate the effects of the nozzle diameter d, nozzle-to-target vertical placement H/d, Rayleigh number, and the jet Reynolds number on the heat transfer rates from a discrete heat source. Simulations were performed for a Prandtl number of 0.7 and for Reynolds numbers ranging from 100 to 5000. The governing equations were solved in the dimensionless form using a commercial finite-volume package. Average Nusselt numbers were obtained, at H/d=3 and two jet diameters, for the bare heat source, for the heat source with a base heat sink, and for the heat source with the finned heat sink. The heat transfer rates from the bare heat source surface have been compared with the ones obtained with the heat sink in order to determine the overall performance of the heat sink in an impingement configuration.

Issue Section:
Research Paper
Keywords:
heat sinks, electronics packaging, plates (structures), cooling, convection, jets, nozzles, flow simulation, finite volume methods, telecommunication
Topics:
Heat sinks, Mixed convection, Reynolds number, Nozzles, Cooling, Computer simulation, Heat, Flow (Dynamics), Rayleigh number
1.
Lee
,
D. Y.
, and
Vafai
,
K.
,
1999
, “
Comparative Analysis of Jet Impingement and Micro Channel Cooling for High Heat Flux Application
,”
Int. J. Heat Mass Transfer
,
42
, pp.
1555
–
1568
.
2.
Sansoucy, E., Oosthuizen, P. H., and Refai-Ahmed, G., 2003, “Enhancement of Air Cooling Limits for Telecom Heat Sink Applications Using Impinging Air Jets,” Proc. of 2003 ASME International Mechanical Engineering Congress & Exposition, ASME, New York.
3.
Sahraoui, M., and Refai-Ahmed, G., 1999, “Flat Plate Fin Heat Sink in Natural Convection Telecommunication Modules,” Advances in Electronic Packaging, ASME, New York, Vol. 26-1.
4.
Kehoe, E., and Davies, M., 2002, “Mixed Convection Cooling of Horizontally Mounted Printed Circuit Board,” Proc. of 2002 Inter Society Conference on Thermal Phenomena.
5.
Deb, P., Basu, B., and Majumdar, P., 1998, “A Comparative Study of Parametric Variation in Forced Convection and Mixed Convection Flow in a Channel With Discrete Heated Modules at High Reynolds Number,” Proc. of 1998 Inter Society Conference on Thermal Phenomena.
6.
Raghavan, J., and Rahman, M., 1996, “Transient Response of a Discrete Heat Source on a Conducting Board in the Presence of Cross Flow Heat Convection,” University of South Florida, 0-7803-3547-3-7/16 IEEE.
7.
Hawkins
,
L. E.
, and
Nelson
,
D. J.
,
1992
, A Design Methodology for Vertical Channel Flow and Heat Transfer,
IEEE Trans. Components, Hybrids, and Manufacturing
,
15
,
761
–
770
.
8.
Cliff, R., Grace, J. R., and Weber, M. E., 1978, Bubbles, Drops, and Particles, Academic Press, New York.
9.
Incropera, F., and DeWitt, D., 2001, Fundamentals of Heat and Mass Transfer, 5th ed. Wiley, New York.
10.
Sikka, K., Fisher, T., and Torrance, K., 1996, “Effect of Wind Tunnel Orientation and Mixed Convection on Heat Transfer from a PFQP,” Proc. 1996 Inter. Society Conference on Thermal Phenomena.
11.
Choi, C. Y., and Ortega, A., 1992, “Mixed Convection in an Inclined Channel With a Discrete Heat Source,” 1992 Proc. Inter. Society Conference on Thermal Phenomena.
12.
Janna, W. S., 2000, Engineering Heat Transfer, 2nd ed., CRC Press, Boca Raton.
Copyright © 2004
 by ASME
You do not currently have access to this content.