In the present work, a compact modeling method based on a volume-averaging technique is presented. Its application to an analysis of fluid flow and heat transfer in straight fin heat sinks is then analyzed. In this study, the straight fin heat sink is modeled as a porous medium through which fluid flows. The volume-averaged momentum and energy equations for developing flow in these heat sinks are obtained using the local volume-averaging method. The permeability and the interstitial heat transfer coefficient required to solve these equations are determined analytically from forced convective flow between infinite parallel plates. To validate the compact model proposed in this paper, three aluminum straight fin heat sinks having a base size of 101.43mm×101.43mm are tested with an inlet velocity ranging from 0.5 m/s to 2 m/s. In the experimental investigation, the heat sink is heated uniformly at the bottom. The resulting pressure drop across the heat sink and the temperature distribution at its bottom are then measured and are compared with those obtained through the porous medium approach. Upon comparison, the porous medium approach is shown to accurately predict the pressure drop and heat transfer characteristics of straight fin heat sinks. In addition, evidence indicates that the entrance effect should be considered in the thermal design of heat sinks when Re Dh/L>∼O10.

Issue Section:
Technical Papers
Keywords:
heat transfer, heat sinks, flow through porous media, forced convection, electronics packaging, permeability, flow simulation, aluminium, temperature distribution
Topics:
Flow (Dynamics), Fluid dynamics, Heat sinks, Heat transfer, Modeling, Porous materials, Temperature distribution, Permeability, Pressure drop
1.
Adams, V. H., Joshi, Y., and Blackburn, D. L., 1997, “Application of Compact Model Methodologies to Natural Convection Cooling of an Array of Electronic Packages in a Low Profile Enclosure,” Proc. The Pacific Rim/ASME International Intersociety Electronic & Photonic Packaging Conference, EEP-Vol. 19-2, E. Suhir et al., eds., The American Society of Mechanical Engineers, New York, pp. 1967–1974.
2.
Andrews
,
J. A.
,
1988
, “
Package Thermal Resistance Model: Dependency on Equipment Design
,”
IEEE Trans. Compon., Hybrids, Manuf. Technol.
,
11
, pp.
528
–
537
.
3.
Mahalingham
,
M.
,
1989
, “
Surface-Mount Plastic Packages-An Assessment of Their Thermal Performance
,”
IEEE Trans. Compon., Hybrids, Manuf. Technol.
,
12
, pp.
745
–
752
.
4.
Joint Electron Device Engineering Council (JEDEC), JC 15.1 Subcommittee, 1995, JEDEC Standard EIA/JESD51-2, “Integrated Circuit Thermal Test Method Environmental Conditions-Natural Convection (Still Air),” developed by Electronic Industries Association (EIA).
5.
Le Jannou
,
J. P.
, and
Huon
,
Y.
,
1991
, “
Representation of Thermal Behavior of Electronic Components for the Creation of a Databank
,”
IEEE Trans. Compon., Hybrid, Manuf. Technol.
,
14
, pp.
366
–
373
.
6.
Bar-Cohen
,
A.
, and
Krueger
,
W.
,
1992
, “
Thermal Characterization of a PLCC-Expanded Rjc Methodology
,”
IEEE Trans. Compon., Hybrids, Manuf. Technol.
,
15
, pp.
691
–
698
.
7.
Aranyosi
,
A.
,
Ortega
,
A.
,
Griffin
,
R. A.
,
West
,
S.
, and
Edwards
,
D. R.
,
2000
, “
Compact Thermal Models of Packages Used in Conduction Cooled Applications
,”
IEEE Trans. Compon., Packag. Manuf. Technol., Part A
,
23
, pp.
470
–
480
.
8.
Ewes, I., 1995, “Modeling of IC-Packages Based on Thermal Characteristics,” Proc. EUROTHERM Seminar No. 45, Sept. 1995, Leuven, Belgium, pp. 11.1–11.12.
9.
Narasimhan
,
S.
, and
Majdalani
,
J.
,
2002
, “
Characterization of Compact Heat Sink Models in Natural Convection
,”
IEEE Trans. Compon., Packag. Manuf. Technol., Part A
,
25
, pp.
78
–
86
.
10.
Koh
,
J. C. Y.
, and
Colony
,
R.
,
1986
, “
Heat Transfer of Microctructures for Integrated Circuits
,”
Int. Commun. Heat Mass Transfer
,
13
, pp.
89
–
98
.
11.
Tuckerman, D. B., 1984, “Heat-Transfer Microstructures for Integrated Circuits,” Ph.D. thesis, Stanford University.
12.
Kim
,
S. J.
, and
Kim
,
D.
,
1999
, “
Forced Convection in Microstructures for Electronic Equipment Cooling
,”
ASME J. Heat Transfer
,
121
, pp.
639
–
645
.
13.
Bejan, A., 1995, Convection Heat Transfer, John Wiley and Sons, New York.
14.
Kaviany, M., 1995, Principles of Heat Transfer in Porous Media, Springer-Verlag, New York.
15.
Slattery, V. C., 1999, Advanced Transport Phenomena, Cambridge University Press, Cambridge, pp. 194–197.
16.
Shah, R. K., and London, A. L., 1978, Laminar Flow Forced Convection in Ducts, Academic Press, London.
17.
Kim
,
S. J.
,
Yoo
,
J. W.
, and
Jang
,
S. P.
,
2002
, “
Thermal Optimization of a Circular-Sectored Finned Tube Using a Porous Medium Approach
,”
ASME J. Heat Transfer
,
124
, pp.
1026
–
1033
.
18.
Blevins, R. D., 1992, Applied Fluid Dynamics Handbook, Krieger Publishing Company, Malabar.
19.
Beckwith, T. G., Marangoni, R. D., and Lienhard, J. H., 1993, Mechanical Measurement, Addison Wesley, New York.
20.
Sparrow
,
E. M.
,
Baliga
,
B. R.
, and
Patankar
,
S. V.
,
1978
, “
Forced Convection Heat Transfer from a Shrouded Fin Array with and without Tip Clearance
,”
ASME J. Heat Transfer
,
100
, pp.
572
–
579
.
21.
Patankar, S. V., 1980, Numerical Heat Transfer and Fluid Flow, Hemisphere Publishing Corp., New York.
Copyright © 2004
 by ASME
You do not currently have access to this content.