This work investigates numerically a catalytic postcombustor for a micro-solid oxide fuel cell (SOFC) system. The postcombustor oxidizes toxic and explosive carbon monoxide (CO) and hydrogen exiting a solid oxide fuel cell to carbon dioxide and water. A single 1 mm diameter monolith reactor channel coated with platinum catalyst is modeled in this work. The inlet stream composition is provided by a semi-analytical 2D model of a detailed SOFC system. The model of the postcombustor includes the 2D axisymmetric Navier–Stokes equations, heat conduction in the channel wall, and a multistep finite-rate mechanism for the surface reactions. It is shown that under the operation conditions considered, the influence of homogeneous (gas phase) reactions can be neglected. The model predicts the expected adiabatic temperatures at the postcombustor outlet correctly and can be used for dimensioning and optimization. Postcombustor performance varies significantly with the choice of the operating parameters of the fuel cell. The most critical molecule at the SOFC outlet is shown to be CO because its depletion is slower than that of for the entire operating range of the SOFC. It can be shown that the postcombustor is able to reduce the level of CO below the toxicity threshold of 25 ppm. Although higher voltages of the fuel cell lead to faster CO conversion in the postcombustor, they also result in a significant increase in wall temperature of the catalyst device. Furthermore, the percentage of SOFC power output used for pump work is lowest for the voltage where the maximum power is reached. For postcombustion the optimal operation point of the SOFC is at the voltage for maximum power of the SOFC system.
Skip Nav Destination
e-mail: dimos.poulikakos@ethz.ch
Article navigation
November 2009
This article was originally published in
Journal of Fuel Cell Science and Technology
Research Papers
Simulation of the Postcombustor for the Treatment of Toxic and Flammable Exhaust Gases of a Micro-Solid Oxide Fuel Cell
N. B. Raberger,
N. B. Raberger
Department of Mechanical and Process Engineering, Laboratory of Thermodynamics in Emerging Technologies,
ETH Zurich
, CH-8092 Zurich, Switzerland
Search for other works by this author on:
M. J. Stutz,
M. J. Stutz
Department of Mechanical and Process Engineering, Laboratory of Thermodynamics in Emerging Technologies,
ETH Zurich
, CH-8092 Zurich, Switzerland
Search for other works by this author on:
N. Hotz,
N. Hotz
Department of Mechanical and Process Engineering, Laboratory of Thermodynamics in Emerging Technologies,
ETH Zurich
, CH-8092 Zurich, Switzerland
Search for other works by this author on:
D. Poulikakos
D. Poulikakos
Department of Mechanical and Process Engineering, Laboratory of Thermodynamics in Emerging Technologies,
e-mail: dimos.poulikakos@ethz.ch
ETH Zurich
, CH-8092 Zurich, Switzerland
Search for other works by this author on:
N. B. Raberger
Department of Mechanical and Process Engineering, Laboratory of Thermodynamics in Emerging Technologies,
ETH Zurich
, CH-8092 Zurich, Switzerland
M. J. Stutz
Department of Mechanical and Process Engineering, Laboratory of Thermodynamics in Emerging Technologies,
ETH Zurich
, CH-8092 Zurich, Switzerland
N. Hotz
Department of Mechanical and Process Engineering, Laboratory of Thermodynamics in Emerging Technologies,
ETH Zurich
, CH-8092 Zurich, Switzerland
D. Poulikakos
Department of Mechanical and Process Engineering, Laboratory of Thermodynamics in Emerging Technologies,
ETH Zurich
, CH-8092 Zurich, Switzerlande-mail: dimos.poulikakos@ethz.ch
J. Fuel Cell Sci. Technol. Nov 2009, 6(4): 041002 (11 pages)
Published Online: August 5, 2009
Article history
Received:
March 27, 2007
Revised:
December 26, 2008
Published:
August 5, 2009
Citation
Raberger, N. B., Stutz, M. J., Hotz, N., and Poulikakos, D. (August 5, 2009). "Simulation of the Postcombustor for the Treatment of Toxic and Flammable Exhaust Gases of a Micro-Solid Oxide Fuel Cell." ASME. J. Fuel Cell Sci. Technol. November 2009; 6(4): 041002. https://doi.org/10.1115/1.3080812
Download citation file:
Get Email Alerts
Cited By
Special Section on 2D Materials for Electrochemical Energy Storage and Conversion
J. Electrochem. En. Conv. Stor (May 2023)
Modified Silicon Anode for Improved Low-Temperature Performance of Lithium-Ion Batteries
J. Electrochem. En. Conv. Stor (February 2024)
CHROMIUM POISONING MITIGATION STRATEGY IN STRONTIUM DOPED LANTHANUM MANGANITE BASED AIR ELECTRODES IN SOLID OXIDE FUEL CELLS
J. Electrochem. En. Conv. Stor
Effect of Liquid Cooling Structure of Confluence Channel on Thermal Performance of Lithium-Ion Batteries
J. Electrochem. En. Conv. Stor (February 2024)
Related Articles
Stainless Steel/Yttria Stabilized Zirconia Composite Supported Solid Oxide Fuel Cell
J. Fuel Cell Sci. Technol (October,2011)
Biosyngas Utilization in Solid Oxide Fuel Cells With Ni ∕ GDC Anodes
J. Fuel Cell Sci. Technol (November,2006)
Modeling Carbon Monoxide Direct Oxidation in Solid Oxide Fuel Cells
J. Fuel Cell Sci. Technol (May,2009)
Investigation of Rapid, Moderate Temperature Change Thermal Cycles of a Micro-Tubular Flame-Assisted Fuel Cell
J. Electrochem. En. Conv. Stor (November,2021)
Related Proceedings Papers
Related Chapters
Lay-Up and Start-Up Practices
Consensus on Operating Practices for Control of Water and Steam Chemistry in Combined Cycle and Cogeneration
Clinical issues and experience
Mechanical Blood Trauma in Circulatory-Assist Devices
Combined Cycle Power Plant
Energy and Power Generation Handbook: Established and Emerging Technologies