Abstract
Precise porosity control is highly desirable for improving the electrochemical performance of solid oxide fuel cells (SOFCs). Freeze casting is an established method for enabling high bulk porosity in structures and controlling pore orientation. In this study, freeze casting was used to fabricate tubular, anode-supported SOFCs with aligned and varying amounts of porosity by controlling the solids/water ratio in different casting slurries. SOFCs were prepared with a Ni/yttria and scandia stabilized zirconia (ScYSZ) anode support (AS), an anode functional layer (AFL), a ScYSZ electrolyte, a lanthanum strontium manganite (LSM)/ScYSZ cathode interlayer (CIL), and an LSM cathode. The permeability of the anode support was found to increase from 1.4 × 10−2 to 1.8 × 10−2 m2 as porosity was increased from 57 to 64 vol%, while the total cell resistance decreased by 35% from 0.93 to 0.60 Ohm cm2. When evaluated with 30 vol% H2 as the fuel at 800 °C, the decrease of concentration polarization enabled an increase in electrochemical performance by 42% from 0.35 to 0.50 W/cm2 as the porosity in the anode support was increased. Mechanical strength characterization using a three-point method showed there is a practical upper limit of the amount of porosity that can be designed into the anode support. This work paves a way for controlling porosity by freeze casting and understanding the correlation between porosity and concentration polarization losses in SOFCs.
Issue Section:
Special Issue: Emerging Investigators in Electrochemical Energy Conversion and Storage 2020
References
1.
Wachsman
, E. D.
, and Lee
, K. T.
, 2011
, “Lowering the Temperature of Solid Oxide Fuel Cells
,” Science
, 334
(6058
), pp. 935
–939
. 10.1126/science.12040902.
Hauth
, M.
, Seidl
, M.
, Postl
, A.
, Sallai
, C.
, Soukup
, N.
, Albert
, J.
, Weinlander
, C.
, Rieberer
, R.
, and Hochenauer
, C.
, 2017
, “Development of a Highly Flexible SOFC CCHP System Towards Demand-Oriented Power Generation From Renewable Fuels,” Solid Oxide Fuel Cells 15
, Vol. 78
, S. C.
Singhal
, and T.
Kawada
, eds., Electrochemical Soc Inc.
, Pennington
, pp. 155
–170
.3.
McPhail
, S. J.
, and Bruno Conti
, J. K.
, 2017
, The Yellow Pages of SOFC Technology International Status of SOFC Deployment 2017
, VTT Technical Research Centre of Finland Ltd.
, Finland
, Vol. 32
, p. 47
.4.
Krist
, K.
, Gleason
, K. J.
, and Wright
, J. D.
, 1999
, SOFC-Based Residential Cogeneration Systems
, Electrochemical Society Inc.
, Pennington
, Vol. 99
, pp. 107
–115
.5.
Huang
, W. H.
, Finnerty
, C.
, Sharp
, R.
, Wang
, K.
, and Balili
, B.
, 2017
, “High-Performance 3D Printed Microtubular Solid Oxide Fuel Cells
,” Adv. Mater. Technol.
, 2
(4
), p. 5
. 10.1002/admt.2016002586.
Lawlor
, V.
, Griesser
, S.
, Buchinger
, G.
, Olabi
, A. G.
, Cordiner
, S.
, and Meissner
, D.
, 2009
, “Review of the Micro-Tubular Solid Oxide Fuel Cell Part I. Stack Design Issues and Research Activities
,” J. Power Sources
, 193
(2
), pp. 387
–399
. 10.1016/j.jpowsour.2009.02.0857.
Mehran
, M. T.
, Park
, S. W.
, Kim
, J.
, Hong
, J. E.
, Lee
, S. B.
, Park
, S. J.
, Song
, R. H.
, Shim
, J. H.
, and Lim
, T. H.
, 2019
, “Performance Characteristics of a Robust and Compact Propane-Fueled 150 W-Class SOFC Power-Generation System
,” Int. J. Hydrogen Energy
, 44
(12
), pp. 6160
–6171
. 10.1016/j.ijhydene.2019.01.0768.
Sammes
, N. M.
, Du
, Y.
, and Bove
, R.
, 2005
, “Design and Fabrication of a 100 W Anode Supported Micro-Tubular SOFC Stack
,” J. Power Sources
, 145
(2
), pp. 428
–434
. 10.1016/j.jpowsour.2005.01.0799.
Iwai
, H.
, Shikazono
, N.
, Matsui
, T.
, Teshima
, H.
, Kishimoto
, M.
, Kishida
, R.
, Hayashi
, D.
, Matsuzaki
, K.
, Kanno
, D.
, Saito
, M.
, Muroyama
, H.
, Eguchi
, K.
, Kasagi
, N.
, and Yoshida
, H.
, 2010
, “Quantification of SOFC Anode Microstructure Based on Dual Beam FIB-SEM Technique
,” J. Power Sources
, 195
(4
), pp. 955
–961
. 10.1016/j.jpowsour.2009.09.00510.
Izzo
, J. R.
, Joshi
, A. S.
, Grew
, K. N.
, Chiu
, W. K. S.
, Tkachuk
, A.
, Wang
, S. H.
, and Yun
, W. B.
, 2008
, “Nondestructive Reconstruction and Analysis of SOFC Anodes Using X-Ray Computed Tomography at Sub-50 nm Resolution
,” J. Electrochem. Soc.
, 155
(5
), pp. B504
–B508
. 10.1149/1.289506711.
Lu
, X. K.
, Li
, T.
, Bertei
, A.
, Cho
, J. I. S.
, Heenan
, T. M. M.
, Rabuni
, M. F.
, Li
, K.
, Brett
, D. J. L.
, and Shearing
, P. R.
, 2018
, “The Application of Hierarchical Structures in Energy Devices: New Insights Into the Design of Solid Oxide Fuel Cells With Enhanced Mass Transport
,” Energy Environ. Sci.
, 11
(9
), pp. 2390
–2403
. 10.1039/C8EE01064A12.
Shri Prakash
, B.
, Senthil Kumar
, S.
, and Aruna
, S. T.
, 2014
, “Properties and Development of Ni/YSZ as an Anode Material in Solid Oxide Fuel Cell: A Review
,” Renew. Sust. Energ. Rev.
, 36
, pp. 149
–179
. 10.1016/j.rser.2014.04.04313.
Fergus
, J. W.
, 2006
, “Electrolytes for Solid Oxide Fuel Cells
,” J. Power Sources
, 162
(1
), pp. 30
–40
. 10.1016/j.jpowsour.2006.06.06214.
Haslam
, J. J.
, Pham
, A. Q.
, Chung
, B. W.
, DiCarlo
, J. F.
, and Glass
, R. S.
, 2005
, “Effects of the Use of Pore Formers on Performance of an Anode Supported Solid Oxide Fuel Cell
,” J. Am. Ceram. Soc.
, 88
(3
), pp. 513
–518
. 10.1111/j.1551-2916.2005.00097.x15.
Luo
, L. H.
, Hou
, B. X.
, Wu
, Y. F.
, Wang
, C. C.
, Cheng
, L.
, Shi
, J. J.
, and Liao
, H. M.
, 2011
, “Effect of Graphite Contents on the Electrochemical Performance of SOFC Prepared by Tape Casting
,” Rare Metal Mat. Eng.
, 40
, pp. 306
–309
.16.
Sarikaya
, A.
, Petrovsky
, V.
, and Dogan
, F.
, 2013
, “Development of the Anode Pore Structure and its Effects on the Performance of Solid Oxide Fuel Cells
,” Int. J. Hydrogen Energy
, 38
(24
), pp. 10081
–10091
. 10.1016/j.ijhydene.2013.05.16017.
Sumi
, H.
, Yamaguchi
, T.
, Hamamoto
, K.
, Suzuki
, T.
, Fujishiro
, Y.
, and Menon
, M.
, 2013
, “Effects of Anode Microstructure on Mechanical and Electrochemical Properties for Anode-Supported Microtubular Solid Oxide Fuel Cells
,” J. Am. Ceram. Soc.
, 96
(11
), pp. 3584
–3588
. 10.1111/jace.1260318.
Suzuki
, T.
, Hasan
, Z.
, Funahashi
, Y.
, Yamaguchi
, T.
, Fujishiro
, Y.
, and Awano
, M.
, 2009
, “Impact of Anode Microstructure on Solid Oxide Fuel Cells
,” Science
, 325
(5942
), pp. 852
–855
. 10.1126/science.117640419.
Jamil
, S. M.
, Othman
, M. H. D.
, Rahman
, M. A.
, Jaafar
, J.
, Ismail
, A. F.
, and Li
, K.
, 2015
, “Recent Fabrication Techniques for Micro-Tubular Solid Oxide Fuel Cell Support: A Review
,” J. Eur. Ceram. Soc.
, 35
(1
), pp. 1
–22
. 10.1016/j.jeurceramsoc.2014.08.03420.
Chen
, Y.
, Bunch
, J.
, Li
, T. S.
, Mao
, Z. P.
, and Chen
, F. L.
, 2012
, “Novel Functionally Graded Acicular Electrode for Solid Oxide Cells Fabricated by the Freeze-Tape-Casting Process
,” J. Power Sources
, 213
, pp. 93
–99
. 10.1016/j.jpowsour.2012.03.10921.
Koh
, Y. H.
, Sun
, J. J.
, and Kim
, H. E.
, 2007
, “Freeze Casting of Porous Ni-YSZ Cermets
,” Mater. Lett.
, 61
(6
), pp. 1283
–1287
. 10.1016/j.matlet.2006.07.00922.
Lichtner
, A. Z.
, Jauffres
, D.
, Martin
, C. L.
, Bordia
, R. K.
, and Kim
, H.-E.
, 2013
, “Processing of Hierarchical and Anisotropic Porosity LSM-YSZ Composites
,” J. Am. Ceram. Soc.
, 96
(9
), pp. 2745
–2753
. 10.1111/jace.1247823.
Lichtner
, A. Z.
, Jauffres
, D.
, Roussel
, D.
, Charlot
, F.
, Martin
, C. L.
, and Bordia
, R. K.
, 2015
, “Dispersion, Connectivity and Tortuosity of Hierarchical Porosity Composite SOFC Cathodes Prepared by Freeze-Casting
,” J. Eur. Ceram. Soc.
, 35
(2
), pp. 585
–595
. 10.1016/j.jeurceramsoc.2014.09.03024.
Miller
, S.
, Xiao
, X. H.
, Setlock
, J.
, Farmer
, S.
, and Faber
, K.
, 2018
, “Freeze-Cast Yttria-Stabilized Zirconia Pore Networks: Effects of Alcohol Additives
,” Int. J. Appl. Ceram. Technol.
, 15
(2
), pp. 296
–306
. 10.1111/ijac.1279425.
Soltani
, N.
, Martinez-Bautista
, R.
, Bahrami
, A.
, Arcos
, L.
, Cassir
, M.
, and Chávez Carvayar
, J.
, 2018
, “Fabrication of Aligned Porous LaNi0.6Fe0.4O3 Perovskite by Water Based Freeze Casting
,” Chem. Phys. Lett.
, 700
, pp. 138
–144
. 10.1016/j.cplett.2018.04.02626.
Moon
, J. W.
, Hwang
, H. J.
, Awano
, M.
, and Maeda
, K.
, 2003
, “Preparation of NiO-YSZ Tubular Support With Radially Aligned Pore Channels
,” Mater. Lett.
, 57
(8
), pp. 1428
–1434
. 10.1016/S0167-577X(02)01002-927.
Du
, Y.
, Persky
, J.
, Zhao
, K.
, Ilkhani
, H.
, Woodson
, T.
, Emley
, B.
, and Hedayat
, N.
, 2017
, “Fabrication and Electrochemical Characterization of Freeze-Cast Tubular Solid Oxide Fuel Cells,” Solid Oxide Fuel Cells 15
, 78
, S. C.
Singhal
, and T.
Kawada
, eds., Electrochemical Soc Inc.
, Pennington
, pp. 1885
–1895
.28.
Panthi
, D.
, Hedayat
, N.
, Woodson
, T.
, Emley
, B. J.
, and Du
, Y.
, 2019
, “Tubular Solid Oxide Fuel Cells Fabricated by a Novel Freeze Casting Method
,” J. Am. Ceram. Soc.
, 103
(2
), pp. 878
–888
.29.
Lankin
, M.
, Du
, Y.
, and Finnerty
, C.
, 2011
, “A Review of the Implications of Silica in Solid Oxide Fuel Cells
,” ASME J. Fuel Cell Sci. Technol.
, 8
(5
), p. 7
. 10.1115/1.400398030.
Cable
, T. L.
, and Sofie
, S. W.
, 2007
, “A Symmetrical, Planar SOFC Design for NASN’s High Specific Power Density Requirements
,” J. Power Sources
, 174
(1
), pp. 221
–227
. 10.1016/j.jpowsour.2007.08.11031.
Sofie
, S. W.
, 2007
, “Fabrication of Functionally Graded and Aligned Porosity in Thin Ceramic Substrates With the Novel Freeze-Tape-Casting Process
,” J. Am. Ceram. Soc.
, 90
(7
), pp. 2024
–2031
. 10.1111/j.1551-2916.2007.01720.x32.
Seub
, J.
, Leloup
, J.
, Richaud
, S.
, Deville
, S.
, Guizard
, C.
, and Stevenson
, A. J.
, 2017
, “Fabrication of Ice-Templated Tubes by Rotational Freezing: Microstructure, Strength, and Permeability
,” J. Eur. Ceram. Soc.
, 37
(6
), pp. 2423
–2429
. 10.1016/j.jeurceramsoc.2017.01.01433.
Gaudillere
, C.
, and Serra
, J. M.
, 2016
, “Freeze-Casting: Fabrication of Highly Porous and Hierarchical Ceramic Supports for Energy Applications
,” Bol. Soc. Esp. Ceram. Vidr.
, 55
(2
), pp. 45
–54
. 10.1016/j.bsecv.2016.02.00234.
Liu
, R. P.
, Xu
, T. T.
, and Wang
, C. A.
, 2016
, “A Review of Fabrication Strategies and Applications of Porous Ceramics Prepared by Freeze-Casting Method
,” Ceram. Int.
, 42
(2
), pp. 2907
–2925
. 10.1016/j.ceramint.2015.10.14835.
Kupecki
, J.
, Kluczowski
, R.
, Papurello
, D.
, Lanzini
, A.
, Kawalec
, M.
, Krauz
, M.
, and Santarelli
, M.
, 2019
, “Characterization of a Circular 80%mm Anode Supported Solid Oxide Fuel Cell (AS-SOFC) With Anode Support Produced Using High-Pressure Injection Molding (HPIM)
,” Int. J. Hydrogen Energy
, 44
(35
), pp. 19405
–19411
. 10.1016/j.ijhydene.2018.02.14336.
Mukhopadhyay
, M.
, Mukhopadhyay
, J.
, and Basu
, R. N.
, 2013
, “Functional Anode Materials for Solid Oxide Fuel Cell—A Review
,” Trans. Indian Ceram. Soc.
, 72
(3
), pp. 145
–168
. 10.1080/0371750X.2013.85162537.
Yan
, Z.
, He
, A.
, Hara
, S.
, and Shikazono
, N.
, 2019
, “Modeling of Solid Oxide Fuel Cell (SOFC) Electrodes From Fabrication to Operation: Correlations Between Microstructures and Electrochemical Performances
,” Energy Conv. Manag.
, 190
, pp. 1
–13
. 10.1016/j.enconman.2019.04.00238.
Chen
, X. W.
, and Hong
, L.
, 2010
, “An In Situ Approach to Create Porous Ceramic Membrane: Polymerization of Acrylamide in a Confined Environment
,” J. Am. Ceram. Soc.
, 93
(1
), pp. 96
–103
. 10.1111/j.1551-2916.2009.03373.x39.
Tjaden
, B.
, Lane
, J.
, Withers
, P. J.
, Bradley
, R. S.
, Brett
, D. J. L.
, and Shearing
, P. R.
, 2016
, “The Application of 3D Imaging Techniques, Simulation and Diffusion Experiments to Explore Transport Properties in Porous Oxygen Transport Membrane Support Materials
,” Solid State Ion.
, 288
, pp. 315
–321
. 10.1016/j.ssi.2016.01.03040.
Barfod
, R.
, Mogensen
, M.
, Klemenso
, T.
, Hagen
, A.
, Liu
, Y.-L.
, and Vang Hendriksen
, P.
, 2007
, “Detailed Characterization of Anode-Supported SOFCs by Impedance Spectroscopy
,” J. Electrochem. Soc.
, 154
(4
), pp. B371
–B378
. 10.1149/1.243331141.
Metzger
, P.
, Friedrich
, K.
, Muller-Steinhagen
, H.
, and Schiller
, G.
, 2006
, “SOFC Characteristics Along the Flow Path
,” Solid State Ion.
, 177
(19–25
), pp. 2045
–2051
. 10.1016/j.ssi.2006.06.01942.
Shimada
, H.
, Suzuki
, T.
, Yamaguchi
, T.
, Sumi
, H.
, Hamamoto
, K.
, and Fujishiro
, Y.
, 2016
, “Challenge for Lowering Concentration Polarization in Solid Oxide Fuel Cells
,” J. Power Sources
, 302
, pp. 53
–60
. 10.1016/j.jpowsour.2015.10.02443.
Liu
, R.
, Cai
, G.
, Li
, J.
, Zhao
, C.
, Wang
, S.
, Wen
, T.
, and Wen
, Z.
, 2010
, “Scandia-Stabilized Zirconia-Impregnated (La, Sr)MnO3 Cathode for Tubular Solid Oxide Fuel Cells
,” J. Solid State Electrochem.
, 14
(10
), pp. 1923
–1928
. 10.1007/s10008-010-1029-544.
Panthi
, D.
, Choi
, B.
, and Tsutsumi
, A.
, 2015
, “Fabrication and Evaluation of a Micro-Tubular Solid Oxide Fuel Cell With an Inert Support Using Scandia-Stabilized Zirconia Electrolyte
,” J. Electrochem. Soc.
, 162
(14
), pp. F1555
–F1560
. 10.1149/2.1031514jes45.
Sholklapper
, T. Z.
, Radmilovic
, V.
, Jacobson
, C. P.
, Visco
, S. J.
, and De Jonghe
, L. C.
, 2006
, “Synthesis and Stability of a Nanoparticle-Infiltrated Solid Oxide Fuel Cell Electrode
,” Electrochem. Solid St.
, 10
(4
), pp. B74
. 10.1149/1.243420346.
Yuan
, C.
, Ye
, X.
, Chen
, Y.
, Chen
, T.
, Liu
, M.
, Li
, J.
, Zhan
, Z.
, and Wang
, S.
, 2014
, “Fabrication of Composite Cathode by a New Process for Anode-Supported Tubular Solid Oxide Fuel Cells
,” Electrochim. Acta
, 149
, pp. 212
–217
. 10.1016/j.electacta.2014.10.06847.
Hsieh
, W.-S.
, Lin
, P.
, and Wang
, S.-F.
, 2013
, “Fabrication of Electrolyte Supported Micro-Tubular SOFCs Using Extrusion and Dip-Coating
,” Int. J. Hydrogen Energy
, 38
(6
), pp. 2859
–2867
. 10.1016/j.ijhydene.2012.12.05648.
Morales
, M.
, and Laguna-Bercero
, M. A.
, 2017
, “Microtubular Solid Oxide Fuel Cells Fabricated by Gel-Casting: The Role of Supporting Microstructure on the Mechanical Properties
,” RSC Adv.
, 7
(29
), pp. 17620
–17628
. 10.1039/C7RA01259D49.
Du
, Y.
, and Sammes
, N. M.
, 2004
, “Fabrication and Properties of Anode-Supported Tubular Solid Oxide Fuel Cells
,” J. Power Sources
, 136
(1
), pp. 66
–71
. 10.1016/j.jpowsour.2004.05.02850.
Mehran
, M. T.
, Khan
, M. Z.
, Lim
, T. H.
, Lee
, S. B.
, and Song
, R. H.
, 2018
, “Effect of Nano-Al2O3 Addition on Mechanical Durability of Nickel-Yttria Stabilized Zirconia Anode Support of Solid Oxide Fuel Cells
,” Ceram. Int.
, 44
(12
), pp. 14824
–14833
. 10.1016/j.ceramint.2018.05.11451.
Driscoll
, D. R.
, Tokmakian
, B. W.
, Johnson
, N. P.
, Hunt
, C. D.
, and Sofie
, S. W.
, 2017
, “Catalyst Enhancing Aluminum Titanate for Increasing Strength of Nickel-Zirconia Cermets
,” Mater. Lett.
, 209
, pp. 307
–310
. 10.1016/j.matlet.2017.08.03552.
Wang
, Y.
, Walter
, M. E.
, Sabolsky
, K.
, and Seabaugh
, M. M.
, 2006
, “Effects of Powder Sizes and Reduction Parameters on the Strength of Ni-YSZ Anodes
,” Solid State Ion.
, 177
(17–18
), pp. 1517
–1527
. 10.1016/j.ssi.2006.07.010Copyright © 2020 by ASME
You do not currently have access to this content.
