To determine the stiffness and damping of computer keyboard keys, a computer-controlled test rig that can measure computer key displacement, velocity, and contact force has been designed. The test rig, consisting of a single-axis stage carrying a probe for contacting keys, has been used to collect contact force and motion data as computer keys are depressed and released at constant velocities up to . Keys that employ a rubber-dome under their caps to achieve the necessary compliance and toggling action were tested. The results demonstrate a nonlinear stiffness force versus displacement characteristic at a given speed and the presence of damping-type forces that increase with key depression speed at a given displacement. In particular, the results indicate that the peak force at the rate of depression increases relative to the quasistatic force level by over 12% for the “Enter,” “K,” and “Spacebar” keys. This paper describes the hardware and software configuration, and presents sample results of the stiffness and damping characteristics of keys during depression-return stroke tests.
Skip Nav Destination
e-mail: mark.nagurka@marquette.edu
e-mail: richard.marklin@marquette.edu
Article navigation
June 2005
Technical Papers
Measurement of Stiffness and Damping Characteristics of Computer Keyboard Keys
Mark Nagurka,
Mark Nagurka
Department of Mechanical and Industrial Engineering,
e-mail: mark.nagurka@marquette.edu
Marquette University
, P.O. Box 1881, Milwaukee, WI 53201-1881, USA
Search for other works by this author on:
Richard Marklin
Richard Marklin
Department of Mechanical and Industrial Engineering,
e-mail: richard.marklin@marquette.edu
Marquette University
, P.O. Box 1881, Milwaukee, WI 53201-1881, USA
Search for other works by this author on:
Mark Nagurka
Department of Mechanical and Industrial Engineering,
Marquette University
, P.O. Box 1881, Milwaukee, WI 53201-1881, USAe-mail: mark.nagurka@marquette.edu
Richard Marklin
Department of Mechanical and Industrial Engineering,
Marquette University
, P.O. Box 1881, Milwaukee, WI 53201-1881, USAe-mail: richard.marklin@marquette.edu
J. Dyn. Sys., Meas., Control. Jun 2005, 127(2): 283-288 (6 pages)
Published Online: June 1, 2005
Citation
Nagurka, M., and Marklin, R. (June 1, 2005). "Measurement of Stiffness and Damping Characteristics of Computer Keyboard Keys." ASME. J. Dyn. Sys., Meas., Control. June 2005; 127(2): 283–288. https://doi.org/10.1115/1.1902823
Download citation file:
Get Email Alerts
A Distributed Multiparticle Precise Stopping Control Model Based on the Distributed Model Predictive Control Algorithm for High-Speed Trains
J. Dyn. Sys., Meas., Control (November 2023)
Performance of Position, Force, and Impedance Controllers for a Pneumatic Cylinder Ankle Exoskeleton
J. Dyn. Sys., Meas., Control (November 2023)
Dual Neural Network Control of a Hybrid FES Cycling System
J. Dyn. Sys., Meas., Control
Impact of Added Passive Compliance On the Performance of Tip-Actuated Flexible Manipulators
J. Dyn. Sys., Meas., Control
Related Articles
Validation of Nonlinear Viscoelastic Contact Force Models for Low Speed Impact
J. Appl. Mech (September,2009)
Air Bearing Force Measurement of Pico Negative Pressure Sliders During Dynamic Unload
J. Tribol (October,2000)
Improving Model Parameters in Vibrating Systems Using Neumann Series
J. Vib. Acoust (February,2019)
Rotordynamic Force Coefficients of Pocket Damper Seals
J. Turbomach (October,2006)
Related Proceedings Papers
Related Chapters
Achievements, Challenges, and Opportunities
Computer Vision for Structural Dynamics and Health Monitoring
Development of a Computer Vision Sensor for Structural Displacement Measurement
Computer Vision for Structural Dynamics and Health Monitoring
Summary and Conclusions
Bearing Dynamic Coefficients in Rotordynamics: Computation Methods and Practical Applications