Inaccuracies in the estimation of material properties and errors in the assignment of these properties into finite element models limit the reliability, accuracy, and precision of quantitative computed tomography (QCT)-based finite element analyses of the vertebra. In this work, a new mesh-independent, material mapping procedure was developed to improve the quality of predictions of vertebral mechanical behavior from QCT-based finite element models. In this procedure, an intermediate step, called the material block model, was introduced to determine the distribution of material properties based on bone mineral density, and these properties were then mapped onto the finite element mesh. A sensitivity study was first conducted on a calibration phantom to understand the influence of the size of the material blocks on the computed bone mineral density. It was observed that varying the material block size produced only marginal changes in the predictions of mineral density. Finite element (FE) analyses were then conducted on a square column-shaped region of the vertebra and also on the entire vertebra in order to study the effect of material block size on the FE-derived outcomes. The predicted values of stiffness for the column and the vertebra decreased with decreasing block size. When these results were compared to those of a mesh convergence analysis, it was found that the influence of element size on vertebral stiffness was less than that of the material block size. This mapping procedure allows the material properties in a finite element study to be determined based on the block size required for an accurate representation of the material field, while the size of the finite elements can be selected independently and based on the required numerical accuracy of the finite element solution. The mesh-independent, material mapping procedure developed in this study could be particularly helpful in improving the accuracy of finite element analyses of vertebroplasty and spine metastases, as these analyses typically require mesh refinement at the interfaces between distinct materials. Moreover, the mapping procedure is not specific to the vertebra and could thus be applied to many other anatomic sites.
Skip Nav Destination
Article navigation
July 2011
Research Papers
A New Material Mapping Procedure for Quantitative Computed Tomography-Based, Continuum Finite Element Analyses of the Vertebra
Ginu U. Unnikrishnan,
Ginu U. Unnikrishnan
Orthopaedic and Developmental Biomechanics Laboratory, Department of Mechanical Engineering,
Boston University
, Boston, MA 02215
Search for other works by this author on:
Elise F. Morgan
Elise F. Morgan
Orthopaedic and Developmental Biomechanics Laboratory, Department of Mechanical Engineering,
Boston University
, Boston, MA 02215
Search for other works by this author on:
Ginu U. Unnikrishnan
Orthopaedic and Developmental Biomechanics Laboratory, Department of Mechanical Engineering,
Boston University
, Boston, MA 02215
Elise F. Morgan
Orthopaedic and Developmental Biomechanics Laboratory, Department of Mechanical Engineering,
Boston University
, Boston, MA 02215J Biomech Eng. Jul 2011, 133(7): 071001 (8 pages)
Published Online: July 13, 2011
Article history
Received:
July 22, 2010
Accepted:
March 27, 2011
Posted:
May 9, 2011
Published:
July 13, 2011
Online:
July 13, 2011
Citation
Unnikrishnan, G. U., and Morgan, E. F. (July 13, 2011). "A New Material Mapping Procedure for Quantitative Computed Tomography-Based, Continuum Finite Element Analyses of the Vertebra." ASME. J Biomech Eng. July 2011; 133(7): 071001. https://doi.org/10.1115/1.4004190
Download citation file:
Get Email Alerts
Related Articles
A New External Fixator Design for Femoral Fracture Reduction
J. Med. Devices (June,2008)
Design of a Dynamic Stabilization Spine Implant
J. Med. Devices (June,2009)
Related Proceedings Papers
Related Chapters
Novel and Efficient Mathematical and Computational Methods for the Analysis and Architecting of Ultralight Cellular Materials and their Macrostructural Responses
Advances in Computers and Information in Engineering Research, Volume 2
Data Tabulations
Structural Shear Joints: Analyses, Properties and Design for Repeat Loading
Research on Oracle Bone Inscriptions Machine Translation Based on Example and Ontology
International Conference on Advanced Computer Theory and Engineering, 4th (ICACTE 2011)