Skip Nav Destination
100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959 : ASTM International, 1982.
ASTM Selected Technical Papers
Selection and Use of Wear Tests for Coatings
By
RG Bayer
RG Bayer
1General Technology Division,
IBM Corporation
, Endicott, New York
; symposium chairman and editor
Search for other works by this author on:
ISBN-10:
0-8031-0710-2
ISBN:
978-0-8031-0710-6
No. of Pages:
487
Publisher:
ASTM International
Publication date:
1982
Bayer, R.
Selection and Use of Wear Tests for Coatings. ISBN-10: 0-8031-0710-2
ISBN: 978-0-8031-0710-6
No. of Pages: 487
ISBN (electronic): 978-0-8031-4834-5
Publisher: ASTM International
Published: 1982
Download citation file:
Table of Contents
-
IntroductionByRG BayerRG Bayer1General Technology Division,IBM Corporation,Endicott, New York;symposium chairman and editorSearch for other works by this author on:
-
Selection and Use of Wear Tests for CoatingsByRF BunshahRF Bunshah1Professor of Engineering, Materials Science and Engineering Department,University of California,Los Angeles, Calif. 90024.Search for other works by this author on:
-
Wear Testing of Abrasion-Resistant Coated PlasticsByLA HaluskaLA Haluska1Associate Development Scientist,Dow Corning Corporation,Midland, Mich. 48640.Search for other works by this author on:
-
Solid Particle Erosion of Coatings on Transparent Polycarbonate and Reinforced CompositesByJ Zahavi,J Zahavi1Israel Institute of Metals,Technion, Haifa,; currently,IsraelVisiting Senior Scientist,IBM Corporation,Poughkeepsie, N.Y. 12602.Search for other works by this author on:GF Schmitt, JrGF Schmitt, Jr2Materials Research Engineer,Materials Laboratory, Air Force Wright Aeronautical Laboratories, Wright-Patterson Air Force Base,Ohio 45433.Search for other works by this author on:
-
Wet-Sand Rubber-Wheel Abrasion Test for Thin CoatingsByGA SaltzmanGA Saltzman1Senior Research Scientist,International Harvester,Hinsdale, Ill. 60521.Search for other works by this author on:
-
Assessment of the Wear of Composite Coatings in Reciprocating Line Contact ConditionsByJK LancasterJK Lancaster1Tribology Section Head, Materials Department,Royal Aircraft Establishment,Farnborough, Hants.,U.K.Search for other works by this author on:
-
Wear Characteristics of Industrial PlatingsByKG BudinskiKG Budinski1Senior Metallurgist,Eastman Kodak Company,Rochester, N.Y. 14650.Search for other works by this author on:
-
Dry Sliding Wear Studies of Nickel-Phosphorus and Chromium Coatings on 0–2 Tool SteelByAW Ruff,AW Ruff1Group Leader, Metallurgy Division, and Chemical Stability and Corrosion Division, respectively,Center for Materials Science, National Bureau of Standards,Washington, D.C. 20234.Search for other works by this author on:DS LashmoreDS Lashmore1Group Leader, Metallurgy Division, and Chemical Stability and Corrosion Division, respectively,Center for Materials Science, National Bureau of Standards,Washington, D.C. 20234.Search for other works by this author on:
-
Methods of Evaluating Materials for Icebreaker Hull CoatingsBySJ Calabrese,SJ Calabrese1Department of Mechanical Engineering,Rensselaer Polytechnic Institute,Troy, N.Y., 12181.Search for other works by this author on:SF MurraySF Murray1Department of Mechanical Engineering,Rensselaer Polytechnic Institute,Troy, N.Y., 12181.Search for other works by this author on:
Email alerts
Copyright
All rights reserved. This material may not be reproduced or copied, in whole or in part, in any printed, mechanical, electronic, film, or other distribution and storage media, without the written consent of the publisher.
© 1982
ASTM International
