... stress intensity factor subsurface flaw finite element analysis Abstract The stress intensity factor (SIF) solutions for subsurface flaws in flat plates are provided in Appendix A of ASME Boiler and Pressure Vessel Code Section XI. A part of the SIF solutions was initially provided...

... ability and higher passability. According to the model introduced in this article, it can provide guidance for the application of sealing cup with internal groove. 1 Copyright © 2024 by ASME Keywords: Pipeline inner inspection tool; Dented defect; Sealing cup; Finite element analysis; Maximum stress...

... laterals, which are the most common in the industry. This paper investigates whether the SIFs of above mentioned 90-degree branch connections can be used for corresponding 45-degree branch connections based on Finite Element Analysis (FEA). In addition, this paper explores the validity of D/T and d/D...

... before the application of ice-plug. ASME code ice-plug cryogenic finite element analysis CANDU fracture Proceedings of the ASME 2024 Pressure Vessels & Piping Conference PVP2024 July 28-August 2, 2024, Bellevue, Washington PVP2024-129996 ON STRUCTURAL INTEGRITY ASSESSMENT OF CONVEYOR TUBE...

... electrofusion joints. electrofusion joint crack propagation failure fracture toughness bursting test finite element analysis Proceedings of the ASME 2024 Pressure Vessels & Piping Conference PVP2024 July 28-August 2, 2024, Bellevue, Washington PVP2024-123193 INVESTIGATION ON CRACK PROPAGATION...

... where traditional methods (e.g: supports or bracing) may not be effective. small-bore piping vibration vibration induced fatigue tuned mass dampers energy institute guidelines finite element analysis screw compressors Proceedings of the ASME 2024 Pressure Vessels & Piping Conference...

...). For finite element analysis (FEA), the 3D Model was generated by considering the actual size and orientation of the windows as required at site. At first, Linear Static Structural Analysis was performed by applying gravity load, and then the solution of the linear static analysis was used to perform...

...) have similar definitions that may need correction. ASME VIII-3 nonmandatory Appendix G clamp preload finite element analysis FEA derivation Proceedings of the ASME 2024 Pressure Vessels & Piping Conference PVP2024 July 28-August 2, 2024, Bellevue, Washington PVP2024-123444 ASME VIII-3...

... evaluation compared to the ASTM E1820 method. J-R curve compliance rotation effect finite element analysis Proceedings of the ASME 2024 Pressure Vessels & Piping Conference PVP2024 July 28-August 2, 2024, Bellevue, Washington PVP2024-121407 EFFECT OF SPECIMEN ROTATION ON CRACK SIZE ESTIMATION...

..., these conventional procedures may assume conservative evaluations, such as merging two close elliptical cracks into a single larger ellipse. In this study, a program based on adaptive meshing through finite element analysis was developed which includes generating crack tip meshes suitable for coalescing multiple...

...-following operating conditions. This study aims to develop a comprehensive numerical model of a light-water reactor pressure vessel (RPV) to investigate its degradation under various operating scenarios. This coupled thermomechanical finite element analysis evaluated the stress response of the RPV caused...

... inputs. The axial welding residual stress and hardness can be reduced by mitigating the axial constraint in the welded joint. stress corrosion cracking stainless steel welding residual stress hardness finite element analysis Proceedings of the ASME 2024 Pressure Vessels & Piping Conference...

... to process variables is essential for analyzing the prevention of PWSCC. Numerous studies have been conducted to predict compressive residual stresses according to process variables, but research on Alloy 600 is insufficient. The finite element analysis methodology is compared to experimental results. Static...

... will remain intact, fuel assembly structural components like guide tubes will remain intact, and no significant VCC sliding or tipping will occur in the range of conditions to be tested with the shake table. spent nuclear fuel seismic analysis finite element analysis Proceedings of the ASME 2024...

... analysis of all storage and transportation scenarios. spent nuclear fuel structural analysis finite element analysis Proceedings of the ASME 2024 Pressure Vessels & Piping Conference PVP2024 July 28-August 2, 2024, Bellevue, Washington PVP2024-125165 STRUCTURAL MODELING TO SUPPORT POST-YIELD...

... unit. Piping stress analysis is performed to calculate stresses by weight and pressure. And remaining life against creep damage is evaluated with ASME B31.3 Appendix V. And detailed finite element analysis is performed under same condition, and creep life is calculated according to API 579 Part 10...

... (laboratory specimen configurations) are developed in this study. elastic-plastic fracture mechanics finite element analysis J -integral Proceedings of the ASME 2023 Pressure Vessels & Piping Conference PVP2023 July 16-21, 2023, Atlanta, Georgia PVP2023-106341 DEVELOPMENT OF A NEW EPRI ELASTIC...

... as further works. stress corrosion cracking stainless steel hardness welding residual stress finite element analysis Proceedings of the ASME 2023 Pressure Vessels & Piping Conference PVP2023 July 16-21, 2023, Atlanta, Georgia PVP2023-103449 MODELING OF HARDNESS AND WELDING RESIDUAL STRESS...

... the differences in creep behavior with both bolted joints and reproduce the observed influence of the previous creep deformation. flange turbine stress relaxation high temperature component testing finite element analysis Proceedings of the ASME 2023 Pressure Vessels & Piping Conference PVP2023 July...

.... spent nuclear fuel seismic analysis finite element analysis Proceedings of the ASME 2023 Pressure Vessels & Piping Conference PVP2023 July 16-21, 2023, Atlanta, Georgia PVP2023-105833 MODELING A SPENT NUCLEAR FUEL CASK SEISMIC TEST Nicholas Klymyshyn1, Kevin Kadooka, James Fitzpatrick, Casey Spitz...