The evaporator recycle streams of nuclear waste tanks may contain waste in a chemistry and temperature regime that exceeds the current corrosion control program, which imposes temperature limits to mitigate caustic stress corrosion cracking (CSCC). A review of the recent service history found that two of these A537 carbon steel tanks were operated in highly concentrated hydroxide solution at high temperature. Visual inspections, experimental testing, and a review of the tank service history have shown that CSCC has occurred in uncooled/un-stress relieved tanks of similar construction. Therefore, it appears that the efficacy of stress relief of welding residual stress is the primary corrosion-limiting mechanism. The objective of this experimental program is to test A537 carbon steel small scale welded U-bend specimens and large welded plates (30.48 × 30.38 × 2.54 cm) in a caustic solution with upper bound chemistry (12 M hydroxide and 1 M each of nitrate, nitrite, and aluminate) and temperature (125 °C). These conditions simulate worst-case situations in these nuclear waste tanks. Both as-welded and stress-relieved specimens have been tested. No evidence of stress corrosion cracking was found in the U-bend specimens after 21 days of testing. The large plate test was completed after 12 weeks of immersion in a similar solution at 125 °C except that the aluminate concentration was reduced to 0.3 M. Visual inspection of the plate revealed that stress corrosion cracking had not initiated from the machined crack tips in the weld or in the heat affected zone. NDE ultrasonic testing also confirmed subsurface cracking did not occur. Based on these results, it can be concluded that the environmental condition of these tests was unable to develop stress corrosion cracking within the test periods for the small welded U-bends and for the large plates, which were welded with an identical procedure as used in the construction of the actual nuclear waste tanks in the 1960s. The absence of evidence of stress corrosion cracking and general corrosion in the laboratory-scaled specimens indicate that this type of nuclear waste tank is not susceptible to highly caustic solutions up to 12 M hydroxide at 125 °C when sufficient nitrite inhibitor is present.
Skip Nav Destination
ASME 2010 Pressure Vessels and Piping Division/K-PVP Conference
July 18–22, 2010
Bellevue, Washington, USA
Conference Sponsors:
- Pressure Vessels and Piping Division
ISBN:
978-0-7918-49255
PROCEEDINGS PAPER
Potential for Stress Corrosion Cracking of A537 Carbon Steel Nuclear Waste Tanks Containing Highly Caustic Solutions
Poh-Sang Lam,
Poh-Sang Lam
Savannah River National Lab (SRNL), Aiken, SC
Search for other works by this author on:
Craig S. Stripling,
Craig S. Stripling
Savannah River National Lab (SRNL), Aiken, SC
Search for other works by this author on:
Donald L. Fisher,
Donald L. Fisher
Savannah River National Lab (SRNL), Aiken, SC
Search for other works by this author on:
James B. Elder, III
James B. Elder, III
Savannah River National Lab (SRNL), Aiken, SC
Search for other works by this author on:
Poh-Sang Lam
Savannah River National Lab (SRNL), Aiken, SC
Craig S. Stripling
Savannah River National Lab (SRNL), Aiken, SC
Donald L. Fisher
Savannah River National Lab (SRNL), Aiken, SC
James B. Elder, III
Savannah River National Lab (SRNL), Aiken, SC
Paper No:
PVP2010-25117, pp. 541-551; 11 pages
Published Online:
January 10, 2011
Citation
Lam, P, Stripling, CS, Fisher, DL, & Elder, JB, III. "Potential for Stress Corrosion Cracking of A537 Carbon Steel Nuclear Waste Tanks Containing Highly Caustic Solutions." Proceedings of the ASME 2010 Pressure Vessels and Piping Division/K-PVP Conference. ASME 2010 Pressure Vessels and Piping Conference: Volume 6, Parts A and B. Bellevue, Washington, USA. July 18–22, 2010. pp. 541-551. ASME. https://doi.org/10.1115/PVP2010-25117
Download citation file:
13
Views
Related Proceedings Papers
Related Articles
Recent Experience in Examination of High-Temperature Catalytic-Cracking Pressure Equipment
Trans. ASME (October,1952)
Elastic-Plastic Fracture Mechanics Analysis on Environmentally Accelerated Cracking of Stainless Steel in High Temperature Water
J. Eng. Mater. Technol (July,1985)
Experimental Study on Crack Growth Behavior for Austenitic Stainless Steel in High Temperature Pure Water
J. Pressure Vessel Technol (May,1986)
Related Chapters
Materials
Power Boilers: A Guide to the Section I of the ASME Boiler and Pressure Vessel Code, Second Edition
Development of Nuclear Boiler and Pressure Vessels in Taiwan
Companion Guide to the ASME Boiler and Pressure Vessel Code, Volume 3, Third Edition
Introduction
Computer Vision for Structural Dynamics and Health Monitoring