This paper presents the strength and damage results based on elastic-plastic analysis to address the design feasibility of pulling in a steel catenary riser (SCR) through a pull tube with various bend configurations in a Spar. The example riser system contains an SCR of typical size, a tapered stress joint, a vertical pull tube with multiple bend sections, guide supports for the pull tube, and the associated pull head and pull chain connected to the top of the riser. The design methods discussed in the paper include: (1) Modeling of riser and pull tube in ABAQUS for strength analysis of the SCR; (2) Strain-based strain-life method to assess the associated fatigue damage; and (3) Strain-based Level 3B ECA design method to derive the critical surface flaw sizes for weld qualification of the SCR inside the pull tube. Comparisons are also presented between results derived from elastic and elastic-plastic analysis methods. The pull-in load on the example SCR increases with the water depth as well as the number and curvature of the bends on the pull tube. Calculated riser pull-in loads are about 11% to 51% higher than the submerged weight of the SCR. The elastic-plastic analysis shows small plastic zone and also small plastic strain on the example SCRs passing through pull tubes of a large bend radius of 125 ft. It also shows large plastic zone but small plastic strain on the SCR in a triple-bend pull tube with a small bend radius of 70 ft. The overall fatigue damage caused by cyclic plastic straining on the example SCRs due to pull in is lower than 3.3%. The allowable surface flaw sizes for the example SCRs are on the order of a × 2c = 8 × 10mm and 2.5 × 40mm for low aspect-ratio and high aspect-ratio surface flaws, respectively. Critical flaw sizes determined by Level 2A ECA are about 25% smaller than the flaw sizes based on Level 3B ECA for low aspect-ratio surface flaws. The specified maximum allowable flaw sizes are not very sensitive to the pull tube configuration and the water depth under the present study. The strength and damage analyses of SCR from other installation methods such as reeling are not included in this paper.
Skip Nav Destination
ASME 2011 30th International Conference on Ocean, Offshore and Arctic Engineering
June 19–24, 2011
Rotterdam, The Netherlands
Conference Sponsors:
- Ocean, Offshore and Arctic Engineering Division
ISBN:
978-0-7918-4436-6
PROCEEDINGS PAPER
Elastic-Plastic Pull-In Strength and Damage Analyses of Steel Catenary Risers in Deepwater
S.-H. Mark Chang
S.-H. Mark Chang
Technip USA, Houston, TX
Search for other works by this author on:
C. H. Luk
Technip USA, Houston, TX
S.-H. Mark Chang
Technip USA, Houston, TX
Paper No:
OMAE2011-49086, pp. 55-65; 11 pages
Published Online:
October 31, 2011
Citation
Luk, CH, & Chang, SM. "Elastic-Plastic Pull-In Strength and Damage Analyses of Steel Catenary Risers in Deepwater." Proceedings of the ASME 2011 30th International Conference on Ocean, Offshore and Arctic Engineering. Volume 4: Pipeline and Riser Technology. Rotterdam, The Netherlands. June 19–24, 2011. pp. 55-65. ASME. https://doi.org/10.1115/OMAE2011-49086
Download citation file:
13
Views
Related Proceedings Papers
Related Articles
Reliable Riser Systems for Spars
J. Offshore Mech. Arct. Eng (November,1999)
Probabilistic Modeling and Analysis of Riser Collision
J. Offshore Mech. Arct. Eng (August,2002)
Linear and Nonlinear Approach of Hydropneumatic Tensioner Modeling for Spar Global Performance
J. Offshore Mech. Arct. Eng (February,2010)
Related Chapters
Production Riser Life Extension – A Class Perspective
Ageing and Life Extension of Offshore Facilities
Insights and Results of the Shutdown PSA for a German SWR 69 Type Reactor (PSAM-0028)
Proceedings of the Eighth International Conference on Probabilistic Safety Assessment & Management (PSAM)
Fatigue Damage Mechanisms in Composite Materials: A Review
Fatigue Mechanisms