Microchannel heat exchangers predominately use a parallel channel configuration to maximize heat transfer with minimal pump demand. Previous work optimized bulk performance of liquid flow heat exchangers but noted that upon boiling, flow redistributed among parallel channels, and they ultimately found that this instability caused an uncontrollable operating condition. This work predicts and measures fully coupled boiling flow interaction in a simplified two microchannel system. A series of silicon microfabricated devices enable piecewise study of the coupled fluidic and heat transfer interactions, first uniting the fluid inlets of thermally isolated channels, then connecting neighboring channel walls to allow heat transfer between channels. Multiple combinations of boiling and liquid flow, each satisfying system boundary conditions, are identified using flow demand curves assembled from single channel data. Each unique flow condition is experimentally demonstrated and found to be heavily dependent on the prior state of the channels. Connecting channel walls, thermally, is shown to lessen the number of allowed solutions and increase instability in the two channel system, allowing distinction between purely fluidic instabilities and fluidic instabilities coupled to heat transfer between channels. This work in describing interaction between two channels is a necessary step as work continues toward characterizing flow boiling in more complex parallel channel heat sinks.

1.
Bergles
A. E.
, and
Kandlikar
S. G.
,
2005
, “
On the Nature of Critical Heat Flux in Microchannels
,”
ASME Journal of Heat Transfer
,
127
(
1)
, pp.
101
107
.
2.
Steinke
M. E.
, and
Kandlikar
S. G.
,
2004
, “
An Experimental Investigation of Flow Boiling Characteristics of Water in Parallel Microchannels
,”
ASME Journal of Heat Transfer
,
126
(
4)
, pp.
518
526
.
3.
Qu
W.
and
Mudawar
I.
,
2004
, “
Transport Phenomena in Two-Phase Micro-Channel Heat Sinks
,”
Journal of Electronic Packaging
,
126
(
2)
, pp.
213
224
.
4.
Xu
J. L.
,
Zhou
H. J.
, et al.
2005
, “
Static and Dynamic Flow Instability of a Parallel Microchannel Heat Sink at High Heat Fluxes
,”
Energy Conversion and Management
,
46
(
2)
, pp.
313
334
.
5.
Kosar
A.
,
Kuo
C. J.
, and
Peles
Y.
,
2006
, “
Suppression of Boiling Flow Oscillations in Parallel Microchannels by Inlet Restrictors
,”
ASME Journal of Heat Transfer
,
128
(
3)
, pp.
251
260
.
6.
Kandlikar
S. G.
,
Kuan
W. K.
,
Willistein
D. A.
, and
Borrelli
J.
,
2006
, “
Stabilization of Flow Boiling in Microchannels Using Pressure Drop Elements and Fabricated Nucleation Sites
,”
ASME Journal of Heat Transfer
,
128
(
4)
, pp.
389
396
.
7.
Boure
J. A.
,
Bergles
A. E.
, and
Tong
L. S.
,
1973
, “
Review of Two-Phase Flow Instability
,”
Nuclear Engineering and Design
,
25
(
2)
, pp.
165
92
.
8.
Li
H. Y.
,
Tseng
F. G.
,
Pan
C.
,
2004
, “
Bubble Dynamics in Microchannels. Part II: Two Parallel Microchannels
,”
International Journal of Heat and Mass Transfer
,
47
(
25)
, pp.
5591
601
.
9.
Flynn, R. D., Kramer, T. A., Koo, J. M., Cheng, C. H., Fogg, D. W., Wang, E. N., and Goodson, K. E., 2005, “Convective Boiling in Silicon Microchannels with Localized Heating and Thermometry,” Paper No. ICMM2005–75209, Third International Conference on Microchannels and Minichannels, ASME, New York.
10.
Daleas, R. S., and Bergles, A. E., 1965, “Effects of Upstream Compressibility on Subcooled Critical Heat Flux,” ASME Paper No. 65-HT 67, ASME, New York.
This content is only available via PDF.
You do not currently have access to this content.