One of the more formidable problems in composite research is the study of delamination and other failure modes in the vicinity of a circular hole in a laminate, e.g., a circular cut-out in a structure. In this problem, the singularity varies around the periphery of the hole as well as through the thickness of the laminate. Under tensile loading, the early failure modes in this problem consist of transverse cracks in various layers, so that delamination occurs only after other damage is precipitated, followed by fiber breakage leading to failure. A literature review of past work clearly shows that mechanical testing with simultaneous AE monitoring is a fruitful technique to study damage accumulation in composite systems. The acoustic-ultrasonic (AU) testing combines the high sensitivity of ultrasonics to internal damage and the method of acoustic emission technique to characterize elastic waves. As damage accumulates in the specimen along the wave path, the net internal damping increases and changes the wave parameters such as velocity, peak amplitude, duration, etc. accordingly. Additionally, a range of experimental results over the last decade has further shown that the mechanical deformation and electric resistance of carbon fiber reinforced polymers are coupled, so that the material is inherently a sensor of its own damage state. The monitoring of electric resistance and capacitance changes, linked to the modifications of the conduction paths in the composite, allows the detection of damage growth. It seems logical that a natural extension of these different approaches is the determination of damage mode, e.g., fiber breakage, matrix cracking or delamination, and damage size and position, based on combined measurements from these techniques. These multiple techniques will serve a two-fold purpose, namely, enable comparison as well as complement each other in case of incomplete damage mapping from one set of sensors For this study, we will consider carbon fiber-reinforced toughened bismaleimide, (IM7/5250-4) quasi-isotropic laminate coupons 12" long, 4" wide with hole at the center under tension. Figure 1 shows the damage which occurs around a 0.75" hole in a [45/0/-45/90]s graphite epoxy laminate obtained by radiography after unloading the test specimen from an applied stress of 50 Ksi. The failure stress for this laminate was 56.4 Ksi. Damage in the form of ply cracks in the 90, 45, and -45 plies and delamination around hole edges is clearly evident. The radiograph taken after unloading from a 50 Ksi stress level clearly shows the location and extent of damage, but contains no specific information about the sequence and the timing of damage events. Figure 2 shows stress-strain curves obtained from strain gages mounted at various distances away from the hole edge along with the far-field value. The stress-strain curves provide useful information regarding the initiation as well as the growth of the damage, as evidenced by jump in strain levels and onset of nonlinearity. Damage initiation is first picked up by the strain gage which is mounted closest to the hole edge at a stress level of 21 Ksi. Subsequently, other strain gages begin to sense damage growth as the applied stress level increases. The strain gage data provides useful information regarding initiation, growth and severity of damage, but it is difficult to assign specific damage modes and their location to the measurements. This example clearly demonstrates the needs, with the associated benefits, of the multiple sensor approach. In this work, three different hole sizes (0.25", 0.5" and 0.75") will be investigated. In addition to inherent resistivity measurements, we will also make strain measurements using gages coupled with simultaneous monitoring of AE events and attenuation of elastic waves using piezoelectric transducers and acceleration sensors. This example problem will enable us to examine the combined effects of cut-outs, matrix cracking, delamination and fiber breakage on the ability of various NDE techniques to assess damage. Integrating several nondestructive evaluation (NDE) techniques could provide a solution for real-time health monitoring.
Skip Nav Destination
ASME 2006 International Mechanical Engineering Congress and
Exposition
November 5–10, 2006
Chicago, Illinois, USA
Conference Sponsors:
- Design Engineering Division and Computers and Information in Engineering Division
ISBN:
0-7918-4767-5
PROCEEDINGS PAPER
Non-Destructive Evaluation of Damage Around Circular Holes in Bolted Composite Laminates
G. P. Tandon,
G. P. Tandon
University of Dayton Research Institute
Search for other works by this author on:
R. Y. Kim
R. Y. Kim
University of Dayton Research Institute
Search for other works by this author on:
G. P. Tandon
University of Dayton Research Institute
R. Y. Kim
University of Dayton Research Institute
Paper No:
IMECE2006-14987, pp. 877-878; 2 pages
Published Online:
December 14, 2007
Citation
Tandon, GP, & Kim, RY. "Non-Destructive Evaluation of Damage Around Circular Holes in Bolted Composite Laminates." Proceedings of the ASME 2006 International Mechanical Engineering Congress and Exposition. Design Engineering and Computers and Information in Engineering, Parts A and B. Chicago, Illinois, USA. November 5–10, 2006. pp. 877-878. ASME. https://doi.org/10.1115/IMECE2006-14987
Download citation file:
13
Views
Related Proceedings Papers
Related Articles
Hygrothermal Damage in Graphite/Epoxy Laminates
J. Eng. Mater. Technol (January,1987)
Enhancement Techniques for Ultrasonic Nondestructive Evaluation of Composite Materials
J. Eng. Mater. Technol (April,1990)
Related Chapters
Understanding the Problem
Design and Application of the Worm Gear
In Situ Observations of the Failure Mechanisms of Hydrided Zircaloy-4
Zirconium in the Nuclear Industry: 20th International Symposium
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design