Metal matrix composites (MMC) are difficult to cut materials, and yet only diamond tools have been successfully utilized for such machining applications. Wear of diamond-coated tools is characterized by catastrophic coating failure (peeling off) due to the adhered work materials at the flank wear-land surface and the high stress developed at the coating-substrate interface, associated with high temperatures, because of very different thermal expansion coefficients. Temperature reductions, therefore, may delay the onset of the coating failure and offer tool life extension. A passive heat-dissipation device, heat-pipe, has been tested for cutting temperature reductions in MMC machining. Though it is intuitive that heat pipes may enhance heat transfer and plausibly reduce the tool temperatures, heat pipes may also increase heat partitioning into the tool, and complicate its effects on the heat removal and temperature reduction efficiency. This paper reports aluminum composite machining by diamond-coated tools and investigates the heat-pipe effects on tool temperature reductions. Numerical simulation of heat conduction in the cutting tool system was performed to evaluate cutting tool temperatures without and with a heat-pipe. A 3-D thermal model of the cutting tool system including coating, insert substrate, and tool holder was established. The heat source was characterized as a heat flux, a portion of the frictional heat flux at the rake face, over the chip-tool contact area. To determine the heat-partition coefficient, a separate 2-D chip model was established with a heat flux, balanced the total rake-face heat flux, over the contact and moving with the chip speed. With the tool and chip thermal models and by matching the average temperature at the tool-chip contact of the two models, the heat partition coefficient can be numerically determined. The model has been used to evaluate how the heat-pipe modifies the cutting tool temperatures. Applying heat-pipe cooling inevitably increases the heat partition into the tool despite the enhanced heat dissipation. However, the heat pipe still effectively reduces the tool-chip contact temperatures, depending upon machining conditions. Cutting tool temperatures have also been measured in machining using thermocouples. The simulation results reasonably agree with the experimental measurements.

1.
Vaccari
J. A.
, and
Lane
C. T.
,
Machining a New Breed of Aluminum
,
American Machinist
,
11
, pp.
56
60
,
1993
.
2.
Andrewes
C. J. E.
,
Feng
H. Y.
, and
Lau
W. M.
,
Machining of an aluminum/sic composite using diamond inserts
.
Journal of Materials Processing Technology
,
102
,
25
29
,
2000
.
3.
Chou, Y. K. and Liu, J., “CVD Diamond Tool Performance in Composite Machining,” Surface and Coating Technologies, in press, May 2005.
4.
May
P. W.
,
CVD Diamond: a New Technology for the Future?
,
Endeavour
,
19
, pp.
101
106
,
1995
.
5.
Heath
P. J.
,
Properties and Uses of Amborite
,
Industrial Diamond Review
,
46
, pp.
120
127
,
1986
.
6.
Hung
N. P.
,
Yeo
S. H.
, and
Oon
B. E.
,
Effect of Cutting Fluid on the Machinability of Metal Matrix Composites
,
Journal of Materials Processing Technology
,
67
, pp.
157
161
,
1997
.
7.
Cronja¨ger
L.
, and
Meister
D.
,
Machining of Fiber and Particle-Reinforced Aluminum
,
Annals of CIRP
,
41
, pp.
63
66
,
1992
.
8.
Sreejith
P. S.
, and
Ngoi
B. K. A.
,
Dry Machining: Machining of the Future
,
Journal of Materials Processing Technology
,
101
, pp.
287
291
,
2000
.
9.
Shen
C. H.
,
Importance of Diamond Coated Tools for Agile Manufacturing and Dry Machining
,
Surface & Coating Technology
,
86–87
, pp.
672
677
,
1996
.
10.
Chi, S.W., Heat Pipe Theory and Practice, Washington D.C.: Hemispere Publishing Corporation, 1976.
11.
Judd
R. L.
,
MacKenzie
H. S.
, and
Elbestawi
M. A.
,
An investigation of a Heat Pipe Cooling System for Use Turning on a Lathe
.
International Journal of Advanced Manufacturing Technology
,
10
(
6
), pp.
357
366
,
1995
.
12.
Jen
T. C.
,
Gutierrez
G.
,
Eapen
S.
,
Barber
G.
,
Zhao
H.
,
Szuba
P. S.
,
Labataille
J.
, and
Manjunathajah
J.
,
Investigation of Heat Pipe Cooling in Drilling Application. part I: Preliminary Numerical Analysis and Verification
.
International Journal of Machine Tools & Manufacture
,
42
, pp.
643
652
,
2002
.
13.
Koepfer, C., Drilling Dry with a Heat Pipe. Retrieved March 15, 2005, from the website: http://www.mmsonline.com/articles/0503rt2.html, 2004.
14.
Chiou, R.Y., Chen, J.S.J., Lin, L., and Cole, L., Prediction of Heat Transfer Behavior of Carbide Inserts with Embedded Heat Pipes for Dry Machining. Proceedings of ASME IMECE, Manufacturing Science and Engineering, pp. 83–90, 2002.
15.
Chiou, R.Y., Chen, J.S.J., Lin, L., and North, M.T., The Effect of an Embedded Heat Pipe in a Cutting Tool on Temperature and Wear. Proceedings of ASME IMECE, IMECE2003-55464, in CD-ROM, 2003.
16.
Shaw, M.C., Metal Cutting Principles. Oxford: Oxford University Press, 1984.
17.
Loewen
E. G.
, and
Shaw
M. C.
, “
On the Analysis of Cutting Temperatures
,”
Transactions of ASME
,
76
, pp.
217
231
,
1954
18.
Nedelik
J.
, and
Lux
B.
,
Improved Tool Performance by Application of Heat-Spreading Diamond Layers within a Multilayer Coating
.
International Journal of Refractory Metals & Hard Materials
,
17
, pp.
275
282
,
1999
.
19.
Kennametal product data. Kennametal tungsten carbide grade K313 nominal properties. Vale, D. private communication, 2003.
20.
ASM committee, ASM handbook (10th ed.). American Society for Metals, 1990.
This content is only available via PDF.
You do not currently have access to this content.