The use of open-cell metal foam in contemporary technologies is increasing rapidly. Certain simplifying assumptions for the combined conduction/convection heat transfer analysis in metal foam have not been exploited. Solving the complete, and coupled, fluid flow and heat transfer governing equations numerically is time consuming. A simplified analytical model for the heat transfer in open-cell metal foam cooled by a low-conductivity fluid is presented. The model assumes local thermal equilibrium between the solid and fluid phases in the foam, and neglects the conduction in the fluid. The local thermal equilibrium assumption is supported by previous studies performed by other workers. The velocity profile in the foam is taken as non-Darcean slug flow. An approximate solution for the temperature profile in the foam is obtained using a similarity transform. The solution for the temperature profile is represented by the error function, which decays in what looks like an exponential fashion as the distance from the heat base increases. The model along with the simplifying assumptions were verified by direct experiment using air and two aluminum foam samples heated from below, for a range of Reynolds numbers. Each foam sample was 5.08 cm-thick in the flow direction. One sample had a pore density of ten pores per inch while the other had twenty pores per inch. Very good agreement was found between the analytical and the experimental results for a considerable range of Reynolds number, with the agreement being generally better for higher Reynolds numbers, and for foam with higher surface area density.
Volume Subject Area:
Heat Transfer
1.
Ashby, M. F., Evans, A. G., Fleck, N. A., Gibson, L. J., Hutchinson J. W. and Wadley, H. N. G., 2000, Metal Foams, A Design Guide, Butterworth-Heinemann, Woburn, MA, pp. 181–188, Chap. 1.
2.
Sullines, D. and Daryabeige, K., 2001, “Effective Thermal Conductivity of High Porosity Open Cell Nickel Foam,” Proc. 35th AIAA Thermophysics Conference, Anaheim, CA.
3.
Vafai
K.
Tien
C. L
1982
, “Boundary and Inertia Effects on Convective Mass Transfer in Porous Media
,” Int. J. Heat and Mass Transfer
, 25
(8
), pp. 1183
–1190
.4.
Bhattacharya
A.
Calmidi
V. V.
Mahajan
R. L.
2002
, “Thermophysical Properties of High Porosity Metal Foams
,” Int. J. Heat and Mass Transfer
, 45
, pp. 1017
–1031
.5.
Bastawros, A. F., 1998, Effectiveness of Open-Cell Metallic Foams for High Power Electronic Cooling, Proc. Symposium on the Thermal Management of Electronics, IMECE, Anaheim, CA.
6.
Bastawros, A. F., Evans, A. G. and Stone, H. A., 1998, “Evaluation of Cellular Metal Heat Transfer Media,” MECH 325, Harvard University, Cambridge, MA.
7.
Hunt
M. L.
Tien
C. L.
1988
, “Effect of Thermal Dispersion on Forced Convection in Fibrous Media
,” Int. J. Heat and Mass Transfer
, 31
(2
), pp. 301
–309
.8.
Boomsma
K.
Poulikakos
D.
2001
, “On the Effective Thermal Conductivity of Three-Dimensionally Structured Fluid-Saturated Metal Foam
,” Int. J. Heat and Mass Transfer
, 44
, pp. 827
–836
.9.
Calmidi
V. V.
Mahajan
R. L.
2000
, “Forced Convection in High Porosity Metal Foams
,” J. Heat Transfer
, 122
, pp. 557
–565
.10.
Hwang
J. J.
Hwang
G. J.
Yeh
R. H.
Chao
C. H.
2002
, “Measurment of the Interstitial Convection Heat Transfer and Frictional Drag for Flow Across Metal Foam
,” J. Heat Transfer
, 124
, pp. 120
–129
.11.
Lu
T. J.
Stone
A.
Ashby
M. F.
1998
, “Heat Transfer in Open-Cell Metal Foam
,” Acta Materialia
, 46
(10
), pp. 3619
–3635
.12.
Lee
D. Y.
Vafia
K.
1999
, “Analytical Characterization and Conceptual Assessment of Solid and Fluid Temperature Differentials in Porous Media
,” Int. J. Heat and Mass Transfer
, 42
, pp. 423
–435
.13.
Angirasa
D.
2002
, “Forced Convective Heat Transfer in Metallic Fibrous Materials
,” J. Heat Transfer
, 124
, pp. 739
–745
.14.
Poulikakos
D.
Renken
K.
1987
, Forced Convection in a Channel Filled with Porous Medium, Including the Effect of Flow Inertia, Variable Porosity, and Brinkman Friction
,” J. Heat Transfer
, 109
, pp. 880
–888
.15.
Poulikakos
D.
Kazmierczak
M.
1987
, “Forced Convection in a Duct Partially Filled with a Porous Material
,” J. Heat Transfer
, 109
, pp. 653
–662
.16.
Kim
S. J.
Jang
S. P.
2002
, “Effects of the Darcy number, the Prandtl Number and the Reynolds Number on the Local Thermal Non-Equilibrium
,” Int. J. Heat and Mass Transfer
, 45
, pp. 3885
–3896
.17.
Vafai
K.
Kim
S. J.
1989
, “Forced Convection in a Channel Filled with a Porous Medium: An Exact Solution
,” J. of Heat Transfer
, 111
, pp. 1103
–1106
.18.
Kaviany, M., 1995, Principles of Heat Transfer in Porous Media, 2nd Ed., Springer, New York, pp. 17, 18, 30, 70, 415.
19.
Narasimhan
A.
Lage
J.
Nield
D. A.
2001
, “New Theory for Forced Convection Through Porous Media by Fluids with Temperature-Dependent Viscosity
,” J. Heat Transfer
, 123
, pp. 1045
–1051
.20.
Ingham, D. B. and Pop, I., 1998, Transport Phenomena in Porous Media, Elsevier Science ltd., Oxford, UK, pp. 103.
21.
Krishnan
S.
Murthy
J. Y.
Garimella
S. V.
2004
, “A Two-Temperature Model for the Analysis of Passive Thermal Control System
,” J. Heat Transfer
, 126
, pp. 628
–637
.22.
Amiri
A.
Vafai
K.
1994
, “Analysis of Dispersion Effects and Non-Thermal Equilibrium, Non-Darcian, Variable Porosity Incompressible Flow Through Porous Media
,” Int. J. Heat and Mass Transfer
, 37
(6
), pp. 939
–954
.23.
Hwang
G. J.
Chao
C. H.
1994
, “Heat Transfer Measurement and Analysis for Sintered Porous Channels
,” J. Heat Transfer
, 116
, pp. 456
–464
.24.
Amiri
A.
Vafai
K.
Kuzay
T. M.
1995
, Effects of Boundary Conditions on Non-Darcian Heat Transfer Through Porous Media and Experimental Comparisons
,” Numerical Heat Transfer Part A: Applications
, 27
, pp. 651
–664
.25.
Alazmi
B.
Vafai
K.
2002
, “Constant Wall Heat Flux Boundary Conditions in Porous Media Under Local Thermal Non-Equilibrium Conditions
,” Int. J. of Heat and Mass Transfer
, 45
, pp. 3071
–3087
.26.
Kim
S. J.
Kim
D.
1999
, “Forced Convection in Microstructures for Electronic Equipment Cooling
,” J. Heat Transfer
, 121
, pp. 639
–645
.27.
Kim
S. J.
Kim
D.
2001
, “The Thermal Interaction at the Interface Between a Porous Medium and an Impermeable Wall
,” J. Heat Transfer
, 123
, pp. 527
–533
.28.
Quintard
M.
Kaviany
M.
Whitaker
S.
1997
, “Two-Medium Treatment of Heat Transfer in Porous Media: Numerical Results for Effectvive Properties
,” Advances in Water Resources
, 20
(2–3
), pp. 77
–94
.29.
Deleglise
M.
Simacek
P.
Binetruy
C.
Advani
S.
2003
, “Determination of the Thermal Dispersion Coefficient During Radial Filling of a Porous Medium
,” J. Heat Transfer
, 125
, pp. 875
–880
.30.
Nield, D. A. and Bejan, A., 1999, Convection in Porous Media, 2nd ed., Springer, New York, pp. 25.
31.
Younis
L. B.
Viskanta
R.
1993
, “Experimental Determiniation of the Volumetric Heat Transfer Coefficient between Stream of Air and Ceramic Foam
,” Int. J. of Heat and Mass Transfer
, 36
(6
), pp. 1425
–1434
.32.
Boomsma
K.
Poulikakos
D.
2002
, “The effect of Compression and Pore Size Variations on the Liquid Flow Characteristics in Metal Foam
,” J. Fluid Engineering
, 124
, pp. 263
–271
.33.
Dukhan, N. and Alvarez, A., 2004, Pressure Drop Measurements for Air Flow through Open-Cell Aluminum Foam, Proc. ASME International Engineering Congress, Anaheim, CA.
34.
Boomsma
K.
Poulikakos
D.
Ventikos
Y.
2003
, “Simulations of Flow Through Open Cell Metal Foams Using an Idelized Periodic Cell Structure
,” Int. J. of Heat and Fluid Flow
, 24
, pp. 825
–834
.35.
Seguin
D.
Montillet
A.
Comiti
J.
1998
, “Experimental Characterisation of Flow Regimes in Various Porous Media- I: Limit of Laminar Flow Regime
,” J. Chemical Engineering Science
, 53
(21
), pp. 3751
–3761
.36.
Calmidi
V. V.
Mahjan
R. L.
1999
, “The Effective Thermal Conductivity of High Porosity Fibrous Metal Foam
,” J. Heat Transfer
, 121
, pp. 466
–471
.37.
Zhao
C. Y.
Lu
T. J.
Jackson
J. D.
2004
, “The Temperature Dependence of Effective Thermal Conductivity of Open-Cell Steel Alloy Foams
,” Materials Science and Engineering
, A 367
, pp. 123
–131
.38.
Zumbrunnen
R.
Viskanta
R.
Incropera
F. P.
1986
, “Heat Transfer Through Porous Solids with Complex Internal Geometries
,” Int. J. Heat and Mass Transfer
, 29
(2
), pp. 275
–284
.39.
ERG Materials and Aerospace, 2003, www.ergaerospace.com, Oakland, CA.
40.
Figliola, R. and Beasly, D., 2000, Theory and Design for Mechanical Measurements, 3rd ed., John Wiley and Sons, New York, pp. 124, 310.
This content is only available via PDF.
Copyright © 2005
by ASME
You do not currently have access to this content.
