The present research is conducted to investigate a critical issue for Lead-free solder alloy. Near-ternary eutectic Sn-Ag-Cu alloys have been studied since they are the leading Lead-free candidate solders for various applications. There are three main phases in the near-ternary eutectic alloys: β-Sn rich phase, Ag3Sn and Cu6Sn5. Cooling rate is an important processing factor that affects the microstructure of these alloys and then significantly influences mechanical behavior of the Sn-Ag-Cu solder joints. It is demonstrated that the amount and size of large Ag3Sn plates increase with decreasing of the cooling rate. When large Ag3Sn plates present in the solder joints at the lower cooling rate, they may affect the mechanical integrity of the joints by providing a crack initialization during the mechanical testing under room-temperature condition. In the present paper, the effects of cooling rate on the microstructure and mechanical properties are studied on Sn-3.8Ag-0.7Cu solder ball, including shear strength and ball pull test. There are two kinds of fracture mode for Ag3Sn plates preformed mechanical loading in room-temperature condition. One is brittle fracture inside Ag3Sn plate itself; the other is interfacial fracture of Ag3Sn plates and the IMC layer. Moreover, the fractures of large Ag3Sn plates induce the decrease of mechanical properties on Sn-3.8Ag-0.7Cu solder ball. The critical cooling rate of large Ag3Sn plate formation is also investigated.

Volume Subject Area:
Electronic and Photonic Packaging
Topics:
Alloys, Cooling, Lead-free solders, Tin, Plates (structures), Fracture (Materials), Fracture (Process), Solders, Mechanical properties, Solder joints, Temperature, Brittle fracture, Eutectic alloys, Mechanical behavior, Mechanical testing, Shear strength
1.
J. H. Lau, C. P. Wong, N. C. Lee and S. W. R. Lee, Electronics Manufacturing with Lead-free, Halogen-free and Conductive Adhesive Materials, McGraw-Hill, New York, (2003).
2.
R. R. Tummala, Fundamentals of Microsystems Packaging, McGraw-Hill, New York, NY, (2001).
3.
Bath
J.
,
Handwerker
C.
, and
Bradley
E.
, “
Research Update: Lead-Free Solder Alternatives
,”
Circuits Assembly
,
11
, (
2000
), pp.
45
–
52
.
4.
Henderson
D. W.
,
Gosselin
T.
,
Sarkhel
A.
,
Kang
S. K.
, et al., “
Ag3Sn Plate Formation in the Solidification of Near-ternary Eutectic Sn-Ag-Cu Alloys
,”
Journal of Materials Research
,
17
(
11
), (
2002
), pp.
2775
–
2777
.
5.
Kang
S. K.
,
Choi
W. K.
,
Shih
D.
, et al., “
Ag3Sn Plate Formation in the Solidification of Near-Ternary Eutectic Sn-Ag-Cu
,”
JOM: Journal of the Minerals, Metals & Materials Society
,
55
(
6
), (
2003
), pp.
61
–
65
.
6.
S. K. Kang, W. K. Choi, D. W. Henderson, et al., “Formation of Ag3Sn Plates in Sn-Ag-Cu Alloys and Optimization of their Alloy Composition,” Proc. 53th Electronic Components & Technology Conference, New Orleans, LA, May (2003), pp. 64–70.
7.
Kang
S. K.
,
Shih
D.
,
Leonard
D.
, et al., “
Controlling Ag3Sn Plate Formation in Near-Ternary-Eutectic Sn-Ag-Cu Solder by Minor Zn Alloying
,”
JOM: Journal of the Minerals, Metals & Materials Society
,
56
(
6
), (
2004
), pp.
34
–
38
.
8.
S. K. Kang, P. Lauro, D. Shih, et al., “Evaluation of Thermal Fatigue Life and Failure Mechanisms of Sn-Ag-Cu Solder Joints with Reduced Ag Contents,” Proc. 54th Electronic Components & Technology Conference, Las Vegas, NV, June (2004), pp. 661–667.
9.
Zeng
K.
and
Tu
K. N.
, “
Six Cases of Reliability Study of Pb-free Solder Joints in Electronic Packaging Technology
,”
Materials Science & Engineering
,
38
, (
2002
), pp.
55
–
105
.
10.
He
M.
,
Chen
Z.
,
Qi
G. J.
, et al., “
Effect of Post-Reflow Cooling Rate in Intermetallic Compound Formation between Sn-3.5Ag Solder and Ni-P under Bump Metallization
,”
Thin Solid Films
,
462–463
, (
2004
), pp.
363
–
369
.
11.
Pack
J.
,
Kim
C.
,
Capper
T.
, et al., “
Phase Equilibria Studies of Sn-Ag-Cu Eutectic Solder Using Differential Cooling of Sn-3.8Ag-0.7Cu Alloys
,”
Journal of Electronic Materials
,
32
(
11
), (
2003
), pp.
1297
–
1302
.
12.
Kim
K. S.
,
Huh
S. H.
and
Suganuma
K.
, “
Effects of Cooling Speed on Microstructure and Tensile Properties of Sn-Ag-Cu Alloys
,”
Materials Science & Engineering A
,
333
, (
2002
), pp.
106
–
114
.
13.
Maveety
J. G.
,
Liu
P.
,
Vijayen
J.
, et al., “
Effect of Cooling Rate on Microstructure and Shear Strength of Pure Sn, Sn-0.7Cu, Sn-3.5Ag, and Sn-37Pb Solders
,”
Journal of Electronic Materials
,
33
(
11
), (
2004
), pp.
1355
–
1362
.
14.
SigelKo
J.
,
Choi
S.
,
Subramanian
K. N.
, et al., “
Effect of Cooling Rate on Microstructure and Mechanical Properties of Eutectic Sn-Ag Solder Joints with and without Intentionally incorporated Cu6Sn5 reinforcements
,”
Journal of Electronic Materials
,
28
(
11
), (
1999
), pp.
1184
–
1188
.
15.
Ocgoa
F.
,
Williams
J. J.
, and
Chawla
N.
, “
Effects of Cooling Rate on the Microstructure and Tensile Behavior of a Sn-3.5wt.%Ag Solder
,”
Journal of Electronic Materials
,
32
(
12
), (
2003
), pp.
1414
–
1420
.
16.
M. Date, T. Shoji, M. Fujiyoshi, et al., “Impact Reliability of Solder Joints,” Proc. 54th Electronic Components and Technology Conference, Las Vegas, NV, June (2004), pp. 668–674.
This content is only available via PDF.
Copyright © 2005
 by ASME
You do not currently have access to this content.