A transient test system was developed for a single cylinder research engine that greatly improves test accuracy by allowing the single cylinder to operate as though it were part of a multi-cylinder engine. The system contains two unique test components: a high bandwidth transient hydrostatic dynamometer, and an intake airflow simulator. The high bandwidth dynamometer is used to produce a speed trajectory for the single cylinder engine that is equivalent to that produced by a multi-cylinder engine. The dynamometer has high torque capacity and low inertia allowing it to simulate the speed ripple of a multi-cylinder engine while the single cylinder engine is firing. Hardware in loop models of the drivetrain and other components can be used to test the engine as though it were part of a complete vehicle, allowing standardized emissions tests to be run. The intake airflow simulator is a specialized intake manifold that uses solenoid air valves and a vacuum pump to draw air from the manifold plenum in a manner that simulates flow to other engine cylinders, which are not present in the single cylinder test configuration. By regulating this flow from the intake manifold, the pressure in the manifold and the flow through the induction system are nearly identical to that of the multi-cylinder application. The intake airflow simulator allows the intake runner wave dynamics to be more representative of the intended multi-cylinder application because the appropriate pressure trajectory is maintained in the intake manifold plenum throughout the engine cycle. The system is ideally suited for engine control development because an actual engine cylinder is used along with a test system capable of generating a wide range of transient test conditions. The ability to perform transient tests with a single cylinder engine may open up new areas of research exploring combustion and flow under transient conditions. The system can also be used for testing the engine under conditions such as cylinder deactivation, fuel cut-off, and engine restart. The improved rotational dynamics and improved intake manifold dynamics of the test system allow the single cylinder engine to be used for control development and emissions testing early in the engine development process. This can reduce development time and cost because it allows hardware problems to be identified before building more expensive multi-cylinder engines.

Volume Subject Area:
Dynamic Systems and Control
Topics:
Cylinder tests (Concrete), Engines, Transients (Dynamics), Cylinders, Flow (Dynamics), Intake manifolds, Single-cylinder engines, Air flow, Dynamometers, Dynamics (Mechanics), Emissions, Engine cylinders, Hardware, Manifolds, Pressure, Testing, Trajectories (Physics), Combustion, Cycles, Electromagnetic induction, Firing, Fuels, Hydrostatics, Inertia (Mechanics), Rotational dynamics, Solenoids, Torque, Vacuum pumps, Valves, Vehicles, Waves
1.
Dorey, R.E., Wang, D., “A Hydrostatic Dynamometer for Engine Testing,” Second Bath International Fluid Power Workshop, Sept. 1989, pp. 153–175, published as part of a Fluid Power Series edited by C.R Burrows and K.A. Edge, “Fluid Power Components and Systems,” Research Studies Press Ltd, John Wiley & Sons Inc.
2.
Ghaffarzadeh, H., Guebeli, M., Vaughan, N.D., “Linear Model Identification of a hydrostatic Dynamometer through Dynamic Simulation,” Fifth Bath International Fluid Power Workshop, Sept. 1992, pp. 416–429, published as part of a Fluid Power Series edited by C.R Burrows and K.A. Edge, “Circuit, Component and System Design,” Research Studies Press Ltd, John Wiley & Sons Inc.
3.
Longstreth, J.C., Sanders, F.A., Seaney, S.P., Moskwa, J.J., Fronczak, F.J., “Design and Construction of a High Bandwidth Hydrostatic Dynamometer,” SAE Transaction 930259, 1993
4.
Moskwa, J.J., Babbitt, G.R., Seaney, S.P., “Development of a High-Bandwidth Hydrostatic Transient Engine Dynamometer System,” ISATA 96AE028, June 1996
5.
Moskwa, J.J., Babbitt, G.R, “Hardware Implementation Details and Test Results for a High-Bandwidth Hydrostatic Transient Engine Dynamometer system,” SAE Transaction 970025, Feb. 1997
6.
Babbitt, G.R., Moskwa, J.J., “Design of an Integrated System for Control and Data Acquisition of a High Bandwidth Hydrostatic Transient Engine Dynamometer System,” Proc. of the American Controls Conference, Albuquerque, NM, 1997
7.
Babbit, G.R., Moskwa, J.J., “Implementation Details and Test Results for a Transient Engine Dynamometer and Hardware in the Loop Vehicle Model,” IEEE CACSD-569, August 1999
8.
Lahti, J.L., Moskwa, J.J., “A Transient Hydrostatic Dynamometer for Testing Single-Cylinder Prototypes of Multi-Cylinder Engines,” SAE 2002-01-0616, March 2002
9.
Lahti, J.L., Moskwa, J.J., “A Transient Hydrostatic Dynamometer for Single Cylinder Engine Research,” IFAC 2283, July 2002
10.
Moskwa
J. J.
,
Lahti
J. L.
, “
Development of a Hardware-in-the-Loop Transient Test System for Single-Cylinder Engines
,”
Powertrain International
, Vol.
6
, No.
3
, Summer
2003
, pp.
14
–
19
11.
Lahti, J.L., Andrasko, S.J., Moskwa, J.J., “A Transient Hydrostatic Dynamometer for Single Cylinder Engine Research with Real Time Multi-Cylinder Dynamic Simulation,” ASME IMECE2003-42748, November 2003
12.
Lahti, J.L., Moskwa, J.J., “A Transient Test System for Single Cylinder Research Engines with Real Time Simulation of Multi-Cylinder Crankshaft and Intake Manifold Dynamics,” SAE 2004-01-0305, March 2004
13.
Moskwa, J.J., Lahti, J.L., “Internal Combustion Engine Simulation and Testing,” United States Patent and Trademark Office, US Patent No. 6708557, March 23, 2004
14.
Moskwa, J.J., Lahti, J.L., Snyder, M.W., “Single Cylinder Engine Transient Test System,” International Journal of Vehicle Design, 2005
This content is only available via PDF.
Copyright © 2005
 by ASME
You do not currently have access to this content.