Concentrating Solar Power (CSP) plants have the potential to provide dispatchable renewable power generation to support the baseload need currently supplied primarily by coal and nuclear plants and peaking power capability to reduce the use of natural gas for load following. However, these plants have had difficulty achieving widespread use due to the low cost of combined photovoltaic and battery systems capable of providing similar services to the electricity grid. A new generation of CSP technologies must be developed to reduce the levelized cost of electricity (LCOE) to 6 cents/kWh by leveraging heat transfer fluids (HTF) capable of operation at higher temperatures and coupling with higher efficiency power conversion cycles. Three promising pathways for Generation 3 CSP (Gen3CSP) technology development have been funded by the U.S. Department of Energy (DOE) leveraging solid, liquid, and gaseous HTFs to transfer heat to a supercritical carbon dioxide (sCO2) Brayton cycle. The primary heat exchangers (PHX) necessary to couple these high-temperature HTFs to sCO 2 are an essential new technology that must be demonstrated at a scale relevant to commercial CSP to validate design expectations for performance, lifetime, and operability. The demonstration of these PHXs need a reliable 1 MWth-scale sCO 2 test system that can provide sCO 2 coolant to the PHX in a compact package suitable for installation near any Gen3CSP thermal storage system. This paper outlines the final design of such a system including the expected operating range and off-design capabilities. The system uses a dense-phase high pressure canned motor pump as the sCO 2 circulator and ambient air as the ultimate heat sink operating at pressures up to 250 bar and temperatures up to 715 °C with capability to supply up to 5.3 kg/s of sCO 2 flow to the primary heat exchanger. Key component requirements for this system have been frozen and procurement is underway. The expected completion date for heated acceptance testing of this system is September of 2020. This system is also capable of being upgraded through the addition of a turbo-compressor and turbo-generator to operate as a complete sCO 2 Brayton cycle with power generation in order to demonstrate an integrated solar to sCO 2 power pilot plant and understand transient interactions between the thermal storage system, sCO 2 turbomachinery, and ambient air temperature. In addition, this upgrade would provide experience with plant operating considerations including balancing charging the thermal storage system with generating and dispatching power to the electrical grid. A roadmap for this upgrade will be discussed including limitations and requirements for the necessary turbomachinery.

Ocean wave is a rich source of renewable energy with much higher power density than winds. Various WEC technologies have been proposed or are under development. In this study, we developed a 2-dimensional (2D) model and analyzed the rotational motion of the lift-type rotor’s blade under steady flow and unsteady flow. The numerical model was validated by experiments under steady flow. Fast Fourier Transform (FFT) analysis was performed to identify the major contribution of frequency in terms of vortexes generated in the flow field. A comparative study was also performed by comparing all the cases in terms of energy conversion efficiency under different wave conditions. It turns out that the efficiency of energy conversion has a maximum value in the steady flow, while the efficiency for unsteady flow keeps decreasing, therefore this is highly due to the increased dissipation because of the oscillating. When the flow is oscillating, the rotational speed of the rotor under periodic condition is lower than the rotational velocity with steady flow, and a curve fitting was performed in this study to predict the periodic average rotational speed. We conclude that for oscillating flow a minimum of 1.6% energy conversion efficiency can be expected, but it may vary for the actual ocean waves. It is expected the current 2D simulation results can contribute to the wave energy community, especially when the rotor design and optimization is required.

A perovskite solar cell in the inverted configuration was modeled and simulated to investigate the impact of the cathode work function on the cell performance. The model utilized the drift-diffusion current equations, coupled with Poisson’s equation and continuity equations to determine the J-V characteristics, the band diagram, and the external quantum efficiencies. It was found the power conversion efficiency (PCE) tended to decrease with the increasing work functions of the metal cathode. The device using low work function metal Ca delivered the best PCE of 16.7%, whereas the one with high work function Au possessed the lowest PCE of 0.3%. These results were in a close agreement with experiments in literature. Photovoltaic parameters (FF, J sc , and V oc ) showed the same tendency and were responsible for the PCE. The band diagram revealed the formation of Schottky barrier was the main reason for the reduction in V oc , and the external quantum efficiency spectrum showed the adverse effect of the Schottky barrier on the charge extraction.

The technical feasibility of off-shore wind energy in the Philippines is assessed. Geographic information system is utilized to integrate the different technical data into a single model. Off-shore wind speed data for five years at elevations 10m, 20m, 80m, and 100m from a local database was used as reference for the wind resource study. Two wind turbines were considered for the energy conversion component, Siemens SWT-3.6-120 and Senvion 6.2 M126. The wind speed data was interpolated to 90m and 95m using standard power law to match the hub heights of the turbines studied. The wind power density, wind power, and annual energy production were calculated from the interpolated wind speeds. Areas in the Philippines with capacity factor greater than 30% and performance greater than 10% were considered technically viable. Exclusion criteria were applied to narrow down the potential siting for offshore wind farms, namely, active submerged cables, local ferry routes, marine protected areas, reefs, oil and gas extraction areas, bathymetry, distance to grid, typhoons, and earthquakes. Several sites were determined to be viable with north of Cagayan having the highest capacity factor. The highest wind capacity factor for the offshore wind farms are located in north of Ilocos Norte (SWT-3.6-120: 54.48%–62.60%; 6.2M126: 54.04%–64.79%), north of Occidental Mindoro (SWT-3.6-120: 46.81%–60.92%; 6.2M126: 45.30%–62.60%) and southeast of Oriental Mindoro (SWT-3.6-120: 45.60%–59.52%; 6.2M126: 45.30%–62.60%). However, these sites are not acceptable due to technical, social, and political constraints. The constraints considered in the study are active submerged cables with a buffer of 5 km, local ferry routes with a buffer of 3km, marine protected areas with a buffer 3 km, reefs with a buffer of 3 km, oil and gas extraction areas with a buffer of 5 km, bathymetry less than 50m, distance to grid of within 120 km, historical typhoon tracks with greater than 250 kph and 50 km buffer, and historical earthquakes with greater than 6.5 magnitude with a buffer of 15 km. Upon application of these exclusion criteria, the potential sites for offshore wind farms are north of Cagayan, west of Rizal, north of Camarines Sur, north of Samar, southwest of Masbate, Dinagat Island, Guimaras, and northeast of Palawan.

The use of pumps as turbines (PAT) has gained importance in the recent years as a possible alternative to specifically developed turbine for mini/micro hydropower plants. The use of production pump for hydropower generation reduces the capital cost of the plant but the energy conversion efficiency can be remarkably lower. The paper analyses the performance of a production centrifugal pump running both in direct and reverse mode. The analysis calculates theoretically the behavior of the PAT under the best efficiency point and extends the investigation to other operating points using both a combined theoretical approach and CFD simulation under dynamic conditions. The effects of possible modifications to the initial design of the pump are investigated when running in turbine mode and their influence on the standard pump operation is also determined. Numerical simulation demonstrates that the impeller trimming leads to improvement in the PAT efficiency in some operating conditions. Conversely, the rotational speeds close to the values typical for the electric generator reduce the PAT performance. Finally, the modification of the impeller geometry at the turbine inlet increases the PAT efficiency but lowers the performance of the machine when running in pump mode.

The paper investigates the performance of a combined heat and power system by means of a fully dynamic numerical approach. An ad-hoc library for the simulation of energy conversion systems is developed under the OpenModelica open source platform; the library includes the main components that usually equip a Combined Heat and Power (CHP) system and they can be connected as they are logically connected in the real plant. Each component is modelled by means of equations and correlations that calculate their performance on a time dependent basis. Therefore, many configurations can be evaluated not only in terms of cumulative annual results or average performance, but the instantaneous behavior can be investigated. The numerical library is constructed using the lumped and distributed parameter approach and it is validated by comparing the numerical results with the measured values over a one-year time period. The prediction capabilities of the proposed numerical approach are evaluated by simulating a case study of a health spa. This case study is selected since it is characterized by significant requirements of both thermal and electric energy. The comparison demonstrated that the calculated results are in good agreement with the measurements in terms of both annual values and distribution over the reference period. Furthermore, an optimization algorithm is adopted and linked to the developed library in order to estimate the best size of different components of the CHP system according to a number of constraints. This feature is particularly important when addressing the energy efficiency of a complete system that is depending on a number of interdependent variables. Therefore, the case study is investigated by accounting also for additional technologies that can be further enhance the performance of the system both in terms of energy consumption and economic investment. In particular, the numerical model is used to optimized the CHP energy efficiency by estimating the best trade-off between the reduction of the energy purchased and the overall cost of the system. The application of PV panels and electric energy accumulators is also investigated and the simulation demonstrates that the size of the cogeneration unit equal to 48 kW, the number of PV panels of 299 and the battery capacity of 45 kWh provide the lowest amount of energy purchased, while the best return of investment is obtained by the CHP unit of 40 kW along with 109 PV panels and a battery of 40 kWh.

Recently, rectennas have drawn attention as an attractive option to harvest radiative thermal energy from the sun and terrestrial thermal sources. In order to achieve the potential high energy conversion efficiencies by this technology, matching conditions between the incident electromagnetic wavelength and the rectenna characteristic length must be satisfied. Therefore, a selective emitter is a key element in high efficiency rectennas. Photonic structures were designed for selective emission using the transfer matrix method and genetic algorithm optimization. Two types of emitters were developed using aluminum as the supporting substrate. This paper presents narrowband selective emitters with a peak emissivity at 9.45 μm made of alternating layers of Al 2 O 3 and SiO 2 on a substrate, and broadband selective emitters made of alternating layers of Al 2 O 3 and SiC on a substrate with a high emissivity band between 9.5 μm and 10.5 μm.

Mixing of fresh (river) water and salty water (seawater or saline brine) in a control fashion would produces an electrical energy known as salinity gradient energy (SGE). Two main conversion technologies of SGE are membrane-based processes; pressure retarded osmosis (PRO) and reverse electrodialysis (RED). In PRO, semipermeable membranes placed between the two streams of solutions allow the transport of water from low-pressure diluted solution to high-pressure concentrated solution. RED requires two alternating semipermeable membranes that allow the diffusion of the ions but not the flow of H 2 O . Lifetime and power density of the semipermeable membrane are two main factors affecting on deployment of PRO and RED. Semipermeable membranes with lifetime greater than 10 years and power density higher than 5 W/m 2 would lead to faster development of this conversion technology. An exergy analysis of an SGE system of sea-river can be applied to calculate the maximum potential power for electricity generation. Seawater is taken as reference environment (global dead state) for calculating the exergy of water since the seawater is the final reservoir. Once the fresh water is mixed with water of the sea or lake it becomes unuseful for human, agricultural or industrial uses loses all its exergy. Aqueous sodium chloride solution model is used in this study to calculate the thermodynamic properties of seawater. This model does not consider seawater as an ideal model and provides accurate thermodynamics properties of sodium chloride solution. As a case study, exergy calculation of Iran’s Urmia Lake-GadarChay River system. The chemical exergy analysis considers sodium chloride (NaCl) as main salt in the water of Lake Urmia. The sodium chloride concentration is more than 200 g/L in recent years. Based on the exergy results the potential power of this system is 329 MW. This results indicates a high potential for constructing power plant for salinity gradient energy conversion.

The ability to efficiently and cost-effectively incorporate thermal energy storage (TES) systems is an important advantage of concentrating solar power (CSP) in comparison to other intermittent forms of renewable energy, such as wind or photovoltaics. As such, TES allows CSP plants to continue to provide electricity to the grid even at times when the resource (the sun) is not available, such as cloud transients or at night. Advanced power cycle systems with supercritical carbon dioxide (sCO2) as the working fluid provide high power conversion efficiency because of high temperatures attained, and less compression work and are being explored for integration with concentrating solar power plants. Currently, there is no cost-effective way to store energy at high temperatures (>565 degree Celsius). The present work analyzes the thermal performance of a novel, cost-effective thermal storage system based on elemental sulfur as the storage media. The analysis is based on a detailed system-level computational modeling of the complex conjugate heat transfer and fluid flow phenomena at multiple scales to provide a scientific basis for engineering, designing and optimizing the novel thermal storage system for transient operation. The validation of the computational model based on data from experiments and full-scale plant operation is also reported. Our studies have shown sulfur-based TES to be a promising candidate for high temperature CSP.

Nuclear reactor systems present a promising sustainable energy source for the future. Simply, a nuclear reactor heats a coolant that powers a turbine to create electricity. The coolant then can either be re-cooled or can be used for process heat applications. By utilizing the heat off the reactor less energy is wasted. A few of the proposed uses of the wasted heat are water desalination, hydrogen production, or pyrolysis. Nuclear power plants most often provide baseload power and are very inflexible. One way to address this is to use nuclear hybrid energy systems. The goal of this research is to create a system that mimics the waste heat from a reactor, demonstrates how to utilize that heat, and shows that when energy demand is low the reactor does not need to reduce power; the energy can be directed elsewhere to create goods. We have developed an Energy Conversion Loop to act as a testbed for experimentation of the aforementioned processes and test the possibility of nuclear hybrid energy systems. The current design consists of a series of heat exchangers that transfer heat between hot air 427 °C (800 °F) and room temperature water. Each loop of the system mimics a type of process that can be tested with a waste heat application. Early models show the system is capable of producing air temperatures near 427 °C (800 °F) and steam temperatures of 154.4 °C (310 °F). These temperatures match needed process heat temperatures for pyrolysis, multi-effect distillation, and multi-stage flash distillation and can be used to simulate other processes for lab scale testing of wasted process heat. Physical testing will be completed in the future to confirm these results.

Small Modular Reactor (SMR) technologies have been recently deemed by the DOE as clean energy, a low carbon-dioxide emitting “alternative energy” source. Recent UN Sustainability Goals and Global Climate Talks to reduce the anthropomorphic Carbon-Dioxide atmospheric concentrations signal a renewed interest and need for nuclear power. The objective of this paper is to present an improved approach to the evaluation of “Hybrid Nuclear Energy Systems”. A hybrid energy system is defined as an energy system that utilizes two or more sources of energy to be used in single or multiple applications. Traditional single sourced energy or power systems require the amount of energy creation and the production of usable power to be carefully balanced. With the introduction of multiple energy sources, loads, and energy capacitors, the design, simulation, and operation of such hybrid systems requires a new approach to analysis and control. This paper introduces three examples of “Hybrid Nuclear Energy Systems”, for large scale power, industrial heat, and electricity generation. The system component independence, reliability, availability, and dynamic control aspects, coupled with component operational decisions presents a new way to optimize energy production and availability. Additional novel hybrid hydro-nuclear systems, concentrated solar-nuclear power desalination systems, and nuclear-insitu petroleum extraction systems are compared. The design aspects of such hybrid systems suitable for process heat, electricity generation, and/or desalination applications are discussed. After a multiple-year research study of past hybrid reactor designs and recent system proposals, the following design evaluation approach is the result of analysis of the best concepts discovered. This review of existing literature has summerized that postulated benefits of Hybrid Nuclear Sytems are; reduced greenhouse gas emissions, increased energy conversion efficiency, high reliability of electricity supply and consistent power quality, reduced fossil fuel dependence, less fresh water consumption, conversion of local coal or shale into higher value fuels, while lowering the risks and costs. As these proposed hybrid systems are interdisciplinary in nature, they will require a new multidisciplinary approach to systems evaluation.

In this paper, experiments that can be introduced to Clean Energy Systems classes are described. The experiments investigate the effect of power characteristics (temperature, shade and tilt angle) on solar panel electricity production. Solar cell efficiency is the ratio of the electrical output of a solar cell to the incident energy in the form of sunlight. The energy conversion efficiency of a solar cell is the percentage of the solar energy to which the cell is exposed that is converted into electrical energy. Extreme temperatures can cause a decrease in solar panel’s power output and airstream can dissipate the heat and bring the solar panel to its normal operating condition. Solar panel efficiency is undesirably affected by heat and improved with introducing cooler medium. As well as heat, solar panel loses its power when a part of it is shaded by trees or surrounding buildings. Before solar panel systems are designed for homes, usually a detailed shading analysis of the roof is conducted to reveal its patterns of shade and sunlight throughout the year. By the same manner, how solar panels react to the direct and indirect rays from the sun in order to produce electricity is examined through experiments. Voltage, current and power flowing into a resistor are measured when the angle of the solar panel relative to the light source is changed. The tilt angles to the electrical measurements are linked to the differences in electrical generation. Students can perform experimental procedures explained here and gain the conceptual understanding of the Solar Energy better. The investigations require student explanation of the question, method, display of data with the critical response from peers.

When buildings of various use-types are served by a district energy system, many societal benefits occur, including improved capacity utilization, reduced energy use, and more cost-effective redundancy. In addition, a central system may benefit financially from commodity leveraging, utility incentives and cogeneration. Energy conversion and transport efficiency for steam and hot water are explored and presented. System optimization curves, including generation and distribution, are presented along with long-term financial comparisons to decentralized systems.

This presentation will discuss the results of the feasibility analysis of a Brayton cycle-based, supercritical CO 2 system that recovers waste heat from an MT30 gas turbine used in marine applications. The analysis also included the use of thermoelectric generator (TEG) devices that are one of several direct energy conversion methods known to be applicable to waste heat recovery. The analysis was conducted by Concepts NREC, in collaboration with the Maine Maritime Academy and their principal consultant, Thermoelectric Power Systems, LLC. The feasibility analysis was conducted under Navy SBIR Proposal Number N103-229-0533, entitled “Gas Turbine Engine Exhaust Waste Heat Recovery Shipboard Module Development”. The objective of the project was to improve the energy efficiency of the MT30 prime-mover power system for the Navy and other commercial vessels. The performance goal for the energy recovery system was to improve the fuel economy of the prime mover by 20% when significantly part-loaded.

Concentrating solar power (CSP) plants can provide dispatchable power with the thermal energy storage (TES) capability for greater renewable-energy grid penetration. To increase the market competitiveness, CSP technology needs to increase the solar-to-electric efficiency and reduce costs in the areas of solar collection from the heliostat field to the receiver, energy conversion systems, and TES. The current state-of-the-art molten-salt systems have limitations regarding both the potential for cost reduction and improvements in performance. Even with significant improvements in operating performance, these systems face major challenges to satisfy the performance targets, which include high-temperature stability (>650°C), low freezing point (<0°C), and material compatibility with high-temperature metals (>650°C) at a reduced cost. The fluidized-bed CSP (FB-CSP) plant being developed by the National Renewable Energy Laboratory (NREL) has the potential to overcome the above issues with substantially lower cost. The particle receiver is a critical component to enable the FB-CSP system. This paper introduces the development of an innovative receiver design using the blackbody design mechanism by collecting solar heat with absorber tubes that transfer the radiant heat to flowing particles. The particle and receiver materials can withstand temperatures of >1000°C because the receiver can use low-cost materials, such as ceramics and stainless steel, and the solid particles can be any low-cost, stable materials such as sand or ash for particle containment and TES. The heated particles can be stored in containers for TES or supply heat for power generation. This study investigated the performance of convection, reflection, and infrared (IR) re-radiation losses on the absorber solar receiving side. We developed a flux model to predict the reflection losses from the absorber tubes based on the NREL SolTrace program, and conducted thermal modeling by using the Fluent Software. This paper presents the thermal modeling and results on the receiver performance. The receiver configuration may have broad applications for different heattransfer fluids (HTFs), including gas, liquid, or the solid particle-based system in our receiver development.

We investigate losses and costs associated with direct steam generation via parabolidal dish concentrators and steam transport to a central steam Rankine power cycle for electricity generation. This study presents a power plant model that accounts for the effects of shading, steam transport, energy conversion at the power block, and capital costs of land and pipework. The pipe network topology used was optimised using a genetic algorithm based on evolution of minimal spanning trees connecting all dishes to a central power block. Optimal pipe sizing of the network is determined by considering the trade-off of frictional losses against thermal losses and material costs. Weather data provides input for the solar resource, and shading is calculated using an established numerical model. The plant model is used to determine the collector layout for which the effective annual revenue is maximised. Results show that the optimal rectangular layout is closely spaced in the North-south direction, along which most of the pipe links run, while East-west spacing is less important. The annual thermal performance of the optimised dish field on a per-unit-area basis is then compared to simulation of a parabolic trough employed for the same purpose. A detailed breakdown of the thermal analysis used forms the basis of comparison between the collector types, giving the overall advantage and a comparison of various sources of loss. We demonstrate that dish fields can collect approximately 49% more thermal energy annually per unit collector area than a trough system employed for the same purpose.

Thermophotovoltaic (TPV) devices are popular energy converters due to providing low noise, low thermal-mechanical stresses and portability. The conversion efficiency of TPVs is still low due to mistuned spectral properties between thermal selective emitters and the TPV cell. Using thermal selective emitters that are well-matched to the TPV cell spectrum enhances the conversion efficiency of TPVs. Several thermal selective emitters, composed of 1-D complex multilayer structures with rectangular gratings, have been proposed. Cost, fabrication and stability factors have been major problems for their application on TPV modules. In this paper, a 1-D tungsten thermal emitter is optimized which exhibits close to blackbody emittance near the band-gap of a GaInAsSb TPV cell and sharp cutoff for longer wavelengths. The emitter is at 1200K, and is designed and optimized by modeling triangular grooves to excite localized groove modes which are well-matched to the GaInAsSb TPV cell external quantum efficiency (EQE) for high efficiency energy conversion. We suggest that a quasi-monochromatic, narrow-band and coherent emitter at a frequency near the energy band-gap of the converter is an ideal source to achieve high conversion efficiency.

In previous work the authors have demonstrated that when hydrogen is combusted in stoichiometric proportions at 1 atm and 1200 K, and singlet oxygen comprises 0–20% of the oxidizer, an optimal range of exergetic efficiency exists. The maximum exergetic efficiency occurs at approximately 10%. Over this range, roughly 60% of the total exergy destruction occurs prior to ignition. This is a significant result because it suggests that the exergetic efficiency of combustion might be improved at a fundamental level by chemical means, thereby inherently increasing the efficiency of fuel use for a desired energy application. The objective of the study presented in this paper is to analyze the reaction mechanisms for combustion with varying percentages of singlet oxygen, to determine which reaction pathways most influence the observed trends in exergy destruction and exergetic efficiency. This was accomplished by performing both sensitivity and rate-of-production analyses of the hydrogen-oxygen combustion mechanism. The results of the analysis show that the presence of singlet oxygen governs the rate of production of hydroxyl and other key radicals. These key radicals directly affect the phenomenological processes associated with chemical induction and thermal induction during ignition. Therefore, the observed optimum exergetic efficiency correlates to the quantity of singlet oxygen in the inlet charge that minimizes exergy destruction by fostering chemical reactions due to radical formation to a greater extent than thermal heat release. The results of this analysis are noteworthy and provide new insight regarding how the exergetic efficiency of combustion may be optimized by introducing singlet oxygen, thereby altering the reaction pathways to enhance energy conversion in a fundamental way that could have important implications for improved fuel use.

Internal combustion (IC) engines typically have an efficiency of less than 35%. This is largely due to the fact that much of the energy dissipates into waste heat. However, the waste heat may be converted into electricity by using energy conversion modules made from bismuth telluride. In this work, it is demonstrated that electricity can be generated from waste heat due to the difference in temperatures. The thermal to electrical energy conversion is achieved by using a self-assembled thermoelectric generator (TEG). The TEG (thermoelectric generator) uses two different types of metallic compound semiconductors, known as n-typed and p-typed, to create voltage when the junctions are held at different temperatures. The work mechanism is based on the Seebeck effect. In this study, the TEGs are made from bismuth telluride (Bi-Te) with relatively high energy conversion efficiencies. In addition, it is readily available. The installation location of the TEG is studied. For testing purposes and convenience, the top of the radiator of a 1990 Mazda Miata car was chosen. The TEG and an aluminum finned heat sink were placed in order on the top of the radiator. Thermal paste was applied to both surfaces and secured with zip ties. A vent was cut on the hood of the car to promote airflow between the fins. Appropriate electrical wiring allowed the unit to output to a digital multi-meter which was located within the car for operator to take data. It is found from the measured results that 0.948 V is the maximum output and the average voltage is 0.751 V. The highest voltage came from driving mountain paths due to the heat sink and coolant temperature being higher than nominal. We estimate that placing an insulator between the heat sink and TEG would push the maximum voltage over 1.0 V. During the cool down phase, the TEG produced electricity continuously with a maximum voltage of 0.9 V right after engine cutoff. The voltage decreased to about 0.6 V within 40 minutes. It is found that the relationship between the temperature difference and output voltage is linear.

The liquefied natural gas (LNG) market has grown significantly and the growth is expected to continue in the future. New technologies that lead to an increased efficiency in each step of the LNG chain are currently under consideration. The studies and the commercial applications associated with the LNG regasification processes can be divided into three large groups: (a) Direct and indirect heat transfer processes between water and LNG; (b) LNG-based co-generation systems, and (c) industrial complexes consisting of an LNG import terminal and an energy-conversion plant, or an energy-intensive chemical plant. In this paper a novel concept for integrating the LNG vaporization into an air separation process is presented. The simulation, energy and exergy analyses are discussed.